Product Data Sheet Show all documents

Sika AnchorFix®-2+

Styrene-free anchoring adhesive for medium to high loads

Solvent and styrene-free, epoxy acrylate based, 2-component anchoring adhesive for normal / moderate climate conditions.

  • Fast curing.
  • Standard guns can be used for application. 
  • High load capacity.
  • ETA to ETAG 001 for anchoring in concrete.
  • ETA to ETAG 001 for rebar connections.
  • Suitable for cracked concrete.
  • Drinking Water certified.
  • LEED Attestation available.
  • Non-sag, even overhead.
  • Styrene-free.
  • Low odour.
  • Low wastage. 
  • Suitable in wet / damp (but clean) holes.
  • Appropriate for marine enviroments. 
Product Data Sheet Show all documents

Usage

As a fast curing anchoring adhesive for all grades of:  
  • Rebars / reinforcing steel
  • Threaded rods
  • Bolts and special fastening systems
  • Concrete (cracked and non-cracked)
  • Solid masonry
  • Steel
  • Hard natural stone*
  • Solid rock*
* These substrates may vary greatly, in particular with regard to strength, composition and porosity. Therefore, for each application the suitability of Sika AnchorFix®-2+ Adhesive must be tested by first applying the product to a sample area. In particular, check bond strength, surface staining and discoloration.  

Advantages

  • Fast curing.
  • Standard guns can be used for application. 
  • High load capacity.
  • ETA to ETAG 001 for anchoring in concrete.
  • ETA to ETAG 001 for rebar connections.
  • Suitable for cracked concrete.
  • Drinking Water certified.
  • LEED Attestation available.
  • Non-sag, even overhead.
  • Styrene-free.
  • Low odour.
  • Low wastage. 
  • Suitable in wet / damp (but clean) holes.
  • Appropriate for marine enviroments. 

Packaging

300 ml standard cartridge

12 cartridges per box

1 pallet: 75 boxes

Colour

Component A: white
Component B: black
Component A+B mixed: grey

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

  • Bonded injection type anchor according to ETAG 001 Part 1 and 5 Option 1, ETA-14/0346, Declaration of Performance 020205010020000011 5034408 (1138), certified by notified product certification body 1020, certificate of constancy of performance 1020-CPR-090-032534, and provided with the CE marking.
  • Post installed rebar connection according to ETAG 001 Part 1 and 5 TR 023, ETA-13/0779, Declaration of Performance 020205010020000011 5034408 (1138), certified by notified product certification body 1020, certificate of constancy of performance 1020-CPD-090-036698, and provided with the CE marking.
  • Drinking Water Certificate: Water Regulations Advisory Scheme Ltd. (WRAS) Approval Number: 1604543.
 
Product Information

Shelf Life

15 months from date of production

All Sika AnchorFix®-2+ cartridges have the expiry date printed on the label.

Storage Conditions

Stored properly in original, unopened, sealed and undamaged packaging in dry conditions at temperatures between +5 °C and +25 °C. Protect from direct sunlight.

Density

~1.62–1.70 kg/l (component A)

~1.44–1.50 kg/l (component B)
~1.60–1.68 kg/l (component A+B mixed)
System information

System Structure

For design details, please refer to the separate documentation provided:
Technical Documentation Sika AnchorFix®-2+ 870 43 06. 
Technical Information

Compressive Strength

~70 N/mm2 (7 days, +20 °C)

(ASTM D 695)

Modulus of Elasticity in Compression

~7 000 N/mm2 (7 days, +20 °C)

(ASTM D 695)

Flexural Strength

~29 N/mm2 (7 days, +20 °C)

(ASTM D 790)

Tensile Strength

~15 N/mm2 (7 days, +20 °C)

(ASTM D 638)

Service Temperature

Long term

-40 °C min. / +50 °C max

Short term (1–2 hours)

+80 °C

Application

Application Information

Mixing Ratio

Component A : Component B = 10 : 1 by volume

Layer Thickness

~5 mm max.

Sag Flow

Non-sag, even overhead

Product Temperature

Sika AnchorFix®-2+ must be at a temperature of between +5 °C and +30 °C for application.

Ambient Air Temperature

+5 °C min. / +30 °C max.

Dew Point

Beware of condensation.
Substrate temperature during application must be at least 3 °C above dew point.

Substrate Temperature

+5 °C min. / +30 °C max.

 

Curing Time

Temperature

Open time - Tgel

Curing time - Tcur

+25 °C to +30 °C

4 minutes

40 minutes

+20 °C to +25 °C

5 minutes

50 minutes

+15 °C to +20 °C

6 minutes

75 minutes

+10 °C to +15 °C8 minutes85 minutes
+5 °C to +10 °C*10 minutes145 minutes

*Minimum cartridge temperature = +5 °C
Application steps

SUBSTRATE QUALITY

Mortar and concrete must be older than 28 days. Substrate strength (for concrete, masonry, natural stone) must be verified. Pull-off tests must be carried out if the substrate strength is unknown. The anchor hole must always be clean and free from oil and grease, etc. Loose particles must be removed from the holes. If applying within flooded holes, the holes must be clean and contain uncontaminated water. Threaded rods and rebars have to be cleaned thoroughly from any oil, grease or any other substances and particles such as dirt, etc.

 

MIXING

Getting the 300 ml cartridge ready:

 

02-en-AnchorFix-1_deck4-24

1. Unscrew the cap.

02-en-AnchorFix-2b_deck4-24

2. Cut the film.

02-en-AnchorFix-3_deck4-24

3. Screw on the static mixing nozzle.

02-en-AnchorFix-4_deck4-24

4. Place the cartridge into the gun and start application.

 

Documents