Sikafloor® MultiDur WT-10
Sikafloor® MultiDur WT-10 is a textured, coloured, water dispersed epoxy floor covering
- Good chemical and mechanical resistance
- Water vapour permeable
- Can be diluted with water
- Odourless
- Easy application
Usage
- Can be subjected to normal up to medium heavy mechanical and chemical loading
- For production areas, warehouses, car park decks, garages, etc.
Advantages
- Good chemical and mechanical resistance
- Water vapour permeable
- Can be diluted with water
- Odourless
- Easy application
Packaging
Please refer to the individual Product Data Sheets
Colour
Available in various colour shades.
Appearance
Textured, semi-gloss finish
System Details
APPROVALS / STANDARDS
- Fire classification in accordance with EN 13501-1, Report-No. PB-Hoch-130019, Germany, January 2013.
System Structure
Sikafloor® MultiDur WT-10 system (~ 0.4-0.6 mm)
1. Primer | Sikafloor®-2540 W+5% wt. water |
2. Top coat | Sikafloor®- 2540 W + Extender T |
Composition
Epoxy waterborne
Nominal Thickness
~ 0.4–0.6mm
Shelf Life
Please refer to the individual Product Data Sheets
Storage Conditions
Please refer to the individual Product Data Sheets
Reaction to Fire
Bfl-S1 | (EN 13501-1) |
Chemical Resistance
Contact Sika technical service for specific information
Thermal Resistance
Exposure* | Dry heat |
Permanent | +60 °C |
Short-term max. 7 d | +80 °C |
Short-term max. 12 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional
(i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Application
Product Temperature
Please refer to the individual Product Data Sheets
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
75 % r.h. max., adequate fresh air ventilation must be provided to remove excess moisture during curing.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
When performing application work with Sikafloor® MultiDur WT-10, the substrate moisture content must not exceed 6 % pbw measured by Tramex.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Waiting Time / Overcoating
Before applying Sikafloor®-2540 W on Sikafloor®-2540 W allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 48 hours | 7 days |
+20 °C | 20 hours | 6 days |
+30 °C | 10 hours | 3 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
When relative air humidity is ≥ 75% the waiting time is increased by at least 24 hours.
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | ~ 48 hours | ~ 5 days | ~ 10 days |
+20 °C | ~ 20 hours | ~ 3 days | ~ 7 days |
+30 °C | ~ 10 hours | ~ 2 days | ~ 5 days |
Consumption
Sikafloor® MultiDur WT-10 system (~ 0.4-0.6 mm)
Coating System | Product | Consumption |
Primer | 1 × Sikafloor®-2540 W + 5 % wt. water | ~0.2–0.3 kg/m² |
Top coat | 1-2 × Sikafloor®- 2540 W + 2 % Extender T | ~0.2–0.3 kg/m² per layer |
CLEANING
Please refer to Sikafloor®‐ Cleaning Regime