Sikafloor® MultiDur ET-18
Sikafloor® MultiDur ET-18 is a 2-part epoxy coloured resin based floor coating system that can provide a hard wearing, seamless, low maintenance textured gloss finish. For medium - heavy wear conditions. Thickness ~ 2–3mm. Internal use.
- Seamless
- Good chemical and mechanical resistance
- Easy application
- Waterproof
- Textured gloss finish
- Easy cleanability
- Slip resistant
- Low maintenance
System Structure
1
Base coat
2
Top Coat
Usage
- On concrete and cementitious screeds with normal up to medium heavy wear e.g. storage and assembly halls, maintenance workshops, garages and loading ramps
- Multi-storey and underground car parks, maintenance hangars and wet process areas, e.g. beverage and food industry
- Floors where slip resistance and easy cleanability is required
Advantages
- Seamless
- Good chemical and mechanical resistance
- Easy application
- Waterproof
- Textured gloss finish
- Easy cleanability
- Slip resistant
- Low maintenance
Packaging
Refer to the individual Product Data Sheets
Colour
Available in many colours
Appearance
Textured, gloss finish
System Details
APPROVALS / STANDARDS
Refer to individual Product Data Sheet within System Structure
System Structure
Sikafloor® MultiDur ET-18 (~ 2–3 mm)
Layer | Product |
1. Primer | Sikafloor®-150/-151 |
2. Wearing coat | Sikafloor®-263 SL N |
3. Top Coat | Sikafloor®-264 N Thixo |
Composition
Epoxy
Nominal Thickness
~ 2–3mm
Shelf Life
Refer to the individual Product Data Sheets
Storage Conditions
Refer to the individual Product Data Sheets
Chemical Resistance
Resistant to many chemicals. Contact Sika Technical Service for specific information.
Thermal Resistance
Exposure | Dry heat |
Permanent | +50 °C |
Short-term max. 7 d | +80 °C |
Short-term max. 12 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Skid / Slip Resistance
R9 | (DIN 51130) |
Application
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
80 % r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
<4 % pbw
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Waiting Time / Overcoating
Before applying Sikafloor®-263 SL N on Sikafloor®-150 /151 allow:
Substrate Temperature | Minimum | Maximum |
+10 °C | 24 hours | 3 days |
+20 °C | 12 hours | 2 days |
+30 °C | 8 hours | 1 day |
Before applying Sikafloor®-264 N Thixo on Sikafloor®-263 SL N allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 30 hours | 3 days |
+20 °C | 24 hours | 2 days |
+30 °C | 16 hours | 1 day |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | ~72 hours | ~6 days | ~10 days |
+20 °C | ~24 hours | ~4 days | ~7 days |
+30 °C | ~18 hours | ~2 days | ~5 days |
Consumption
Sikafloor® MultiDur ET-18 (~ 2–3 mm)
Coating System | Product | Consumption |
1.Primer | 1 × Sikafloor®-150/-151 | ~0.3–0.5 kg/m² |
2.Wearing coat | 1 × Sikafloor®- 263 SL N filled 1:1 with quartz sand 0.06–0.3mm | ~4 kg/m2 (2 kg/m2 binder + 2 kg/m2 quartz sand) |
3.Top coat | 1–2 × Sikafloor®- 264 N Thixo | ~0.5–0.8 kg/m2 per layer |
CLEANING
Refer to the Information Manual Sikafloor®-Cleaning Regime