Sika® Separol W

Sika® Separol® W is a ready to use, solvent and mineral oil free concrete release
agent. It is an emulsion, based on biological degradable synthetic oil.

USES

Sika® Separol®W can be applied on sites and in precast plants.


Sika® Separol® W is mainly used for the following applications:

  • Smooth non-absorbent formwork
  • Absorbent formwork
  • Heated formwork (up to +70°C)
  • Textured formwork

CHARACTERISTICS & ADVANTAGES

Sika® Separol® W has the following characteristics:

  • Excellent ‘sticking’ ability on vertical mould surfaces
  • Self levelling after spray application
  • Non combustible vapour
  • Reduced ‘dusty’ residues on the formwork
  • Safe for the operatives to handle

This provides the following advantages:

  • Easy and precise separation of the formwork from the hardened concrete
  • High quality surface finish
  • No reduction of the concrete quality at the surface
  • Protection of formwork from steel corrosion and early ageing

 

DOWNLOAD

Product Data Sheet | Safety Data Sheet |

Sika® Curehard 24

Sikafloor®-CureHard-24 is a one part, clear liquid based on sodium silicate to cure,
harden and seal fresh or hardened concrete.

USES

  • Horizontal old or new concrete surfaces, where a hard surface with light to
    moderate abrasion resistance is required e.g. warehouses, industrial plants,
    stores, shopping malls, parking structures, service stations, hangars etc.
  • On concrete slabs where no specific curing efficiency or standards are
    required
  • Suitable for interior or exterior applications

CHARACTERISTICS & ADVANTAGES

  • Ready to use
  • Easy to apply
  • Improved chemical and abrasion resistance compared to untreated concrete
  • Reduced dusting of concrete floors
  • Reduced loss of water of new concrete while setting
  • Improves cleanability
  • Non-yellowing
  • Good penetration
  • Solvent free
  • Colourless and odourless
  • Environmentally friendly

 

DOWNLOAD

Product Data Sheet | Safety Data Sheet |

Sika® Rugasol Plus

Sika Rugasol® Plus surface retarder have been specially designed
for producing a mechanical key to construction joints, stop ends, or subsequent rendering applications.

USES

Sika Rugasol® Plus is particularly suitable to provide exposed aggregate finishes for :

  • Concrete pavements
  • Pedestrian areas
  • Court yards

This product was developed for concrete with a maximum aggregate size of 12 to 20 mm. Deactivation depth is between 4 and 6mm.

CHARACTERISTICS & ADVANTAGES

Sika Rugasol® Plus provides a concrete which has the following advantages:

  • Visually appealing finishes “exposed aggregate”
  • Slip: Reduces the risk of aquaplaning for vehicles and slides for pedestrians
  • Better resistance to stresses

 

DOWNLOAD

Product Data Sheet | Safety Data Sheet |

Sika® Proseal W

Sikafloor®-ProSeal W is a one part water dispersed acrylic emulsion to cure,
harden and seal fresh or hardened concrete.

USES

  • Sikafloor®-ProSeal W is used for optimum curing and sealing of fresh concrete floors and structures
  • Curing compound in order to limit surface drying and cracking
  • Provides curing and sealing for Sikafloor® dry shake hardeners
  • Anti-dust treatment and improvement of the abrasion resistance of existing concrete surfaces
  • Suitable for exterior and interior application

CHARACTERISTICS & ADVANTAGES

  • Excellent moisture retention; meets requirements of ASTM C-309
  • Water dispersion
  • Suitable for indoor use where solvent-based products cannot be applied because of health and safety regulations
  • Helps control dusting for both new and existing concrete floor surfaces
  • Effectively cures and seals concrete surfaces in a single, economic operation
  • Non yellowing
  • Easy application by spray or roller

 

DOWNLOAD

Product Data Sheet | Safety Data Sheet |

Sika® SprayGard

Sika® SprayGard® is a ready to use, blend of selected oils developed to protect concrete mixing equipment.

USES

Sika® SprayGard® can be applied on all mixing equipment that is in contact with fresh concrete and mortar.


Sika® SprayGard® is mainly used for the following applications:

  • A wide range of applications where mixing equipment requires protection
  • Forced action concrete and mortar mixes
  • Truck mixers and drums

CHARACTERISTICS & ADVANTAGES

Sika® SprayGard® allows for an increased service life of all mixing and transportation equipment.

  • Excellent “sticking” ability
  • Reduces corrosive action of cement on metal surfaces
  • Extended service life of equipment
  • Easy to use

 

DOWNLOAD

Product Data Sheet | Safety Data Sheet |

Sika® TR5

Sika® TR 5 is a ready to use, solvent free release agent. It is based on mineral oil and wax.

USES

Sika® TR 5 can be applied on sites and in precast plants.


It has been specially developed for use on:

  • Smooth non-absorbent formwork
  • Absorbent formwork
  • Heated formwork (up to +70°C)

Sika® TR 5 is also suitable for:

  • Textured formwork

CHARACTERISTICS & ADVANTAGES

Sika® TR 5 has the following characteristics:

  • Low viscous
  • Excellent ‘sticking’ ability on vertical mould surfaces
  • Self leveling after spray application
  • Highly pore suppressing
  • No combustible vapor
  • No creation of resin
  • Reduced ‘dusty’ residues on the formwork
  • Safe for the operatives to handle

This provides the following advantages:

  • Easy and precise separation of the formwork from the hardened concrete
  • High quality surface finish
  • No reduction of the concrete quality at the surface
  • Protection of formwork from steel corrosion and early ageing

 

DOWNLOAD

Product Data Sheet | Safety Data Sheet |

Sika® TR6

Sika® TR 6 is a ready to use, solvent free mold release agent. It is an emulsion, based on a refined mineral oil.

USES

Sika® TR 6 is suitable for a wide range of applications.


It has been specially developed for:

  • Smooth non-absorbent formwork
  • Absorbent formwork
  • Heated formwork (up to +70°C)

Adhesion of subsequent coatings (e.g. renderings, paints, adhesive, etc) is normally not affected.

CHARACTERISTICS & ADVANTAGES

Sika® TR 6 is a ready to use, solvent and mineral oil free release agent emulsion,
based on natural grease substances and synthetic oil.


It has the following characteristics:

  • Reduced smell intensity
  • Economic consumption
  • Physical and chemical release properties avoid adhesion of concrete on the formwork
  • High quality concrete surfaces are obtained using the given consumption quantity
  • Special additives (increased quantity) act as rust inhibitors and prolong the service life of timber formwork

 

DOWNLOAD

Product Data Sheet | Safety Data Sheet |