Product Data Sheet Show all documents
EVERBUILD® 720 FEBFLOR FibrePlus

EVERBUILD® 720 FEBFLOR FibrePlus

Fibre Modified Self Levelling Compound

EVERBUILD® 720 FEBFLOR FibrePlus is a fibre modified, cement based, protein free powder. When mixed with water, EVERBUILD® 720 FEBFLOR FibrePlus can be used to level out uneven floors and screeds. This product contains powdered polymer, thus eliminating the need for separate expensive latex liquids. When mixed as directed, EVERBUILD® 720 FEBFLOR FibrePlus provides a free flowing mix that sets in just 4 hours and can be overlaid after only 8 hours.

  • Can be used up to 60 mm in depth in one application.
  • Designed for the embedment of underfloor heating systems.
  • Contains powdered polymer - no need for latex liquid.
  • Will not crack or shrink, even in the most demanding applications.
  • Free flowing formula.
  • Sets in 4 hours.
  • Can be overlaid in 8 hours.
  • Heat resistant.
Product Data Sheet Show all documents

Usage

Suitable for
  • Concrete
  • Screed
  • Ceramic tiles
  • Thermoplastic tiles
  • Lino
  • Wood block floorings
  • Carpet
  • Asphalt
  • Brick
  • Stone
This product is suitable for the embedment of underfloor heating. Note: This product is NOT suitable for use as a final wearing surface.  

Advantages

  • Can be used up to 60 mm in depth in one application.
  • Designed for the embedment of underfloor heating systems.
  • Contains powdered polymer - no need for latex liquid.
  • Will not crack or shrink, even in the most demanding applications.
  • Free flowing formula.
  • Sets in 4 hours.
  • Can be overlaid in 8 hours.
  • Heat resistant.

Packaging

20 kg paper bag

Colour

Grey

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

EN 13813 Class CT-C30-F6
Product Information

Chemical Base

Cement, sand and specialist additives

Shelf Life

6 months (when stored as directed)

Storage Conditions

This product must be stored in unopened bags, clear of the ground, in cool dry conditions and protected from excessive draught
Technical Information

Compressive Strength

31.7 MPa

Flexural Strength

6.59 MPa

Reaction to Fire

A1/A1fl

Application

Application Information

Layer Thickness

3 mm to 60 mm.

Ambient Air Temperature

+5 °C to +20 °C

Pot Life

40 mins

Setting time

Accepts traffic- 4 hours

Floor coverings - 8 hours
Consumption

Yield

1.8 kg/m2/mm

4.3 m2 @ 3 mm depth
Application steps

APPLICATION

  • Floors to be treated must be free from grease, dust and loose particles.
  • Always prepare floors by dampening with water and then priming with Everbuild® Contractor PVA or 503 SBR 1 part to 3 parts water for wood or cement based substrates.  Sika® Level-01 Primer 1 part to 3 parts water can be used on other substrates to give a sound surface.
  • EVERBUILD® 720 FEBFLOR FibrePlus will require 3.4 litres of water. DO NOT USE EXCESS WATER.
  • Always add the powder to the water - this should be carried out by stepwise addition whilst stirring until a free flowing creamy compound is produced.
  • Pour the admixture out into the prepared floor and allow it to find its own level.
  • Trowel down lightly to achieve an overall thickness not exceeding 60 mm.
  • Where further finishing is required, allow the surface to stiffen, usually 45 minutes to one hour after application, and lightly sprinkle with water and carefully trowel to produce a smooth appearance.
  • Do not sprinkle excessive water or over trowel at this stage.
  • Additional layers, each not exceeding 60 mm, may be applied to achieve the required depth only when the first coat is dry (8 hours minimum @20 °C).
  • Prime with  Everbuild® Contractor PVA or 503 SBR diluted 1 part to 3 parts water between layers.

Timber Floors, Existing Tiling and Asphalt

  • Degrease and roughen up any glaze on existing tiling or asphalt prior to laying this product.
  • Timber floors must be securely screwed down at 300 mm centres.
  • In all cases, Everbuild® Contractor PVA or 503 SBR to the floor at a 1:3 dilution with water.   
  • For especially porous substrates, 2 coats of primer should be used, the first diluted 1:4 with water and allowed to dry before applying the second.
  • For substrates with limited porosity use Everbuild® Contractor PVA or 503 SBR in 1 coat diluted 1:3 with clean water.
  • Mix EVERBUILD® 720 FEBFLOR FibrePlus with water as directed and apply to sub floor whilst the bonding coat is still tacky.

CLEANING OF TOOLS

After use, clean tools in water. Wash hands immediately after using this product.

Documents