Product Data Sheet Show all documents
EVERBUILD® EpoxySET NF

EVERBUILD® EpoxySET NF

Expoxy adhesive & bedding compound

EVERBUILD® EpoxySET NF is an epoxy resin bedding compound which has been designed for use where a non-slumping type of epoxy bedding compound is required. It is a two-pack, fine aggregate filled, fast-curing material, ideal for a variety of bedding, gap filling and concrete repair applications. EVERBUILD® EpoxySET NF is a stiff but easily workable compound that can be applied by either trowel, spatula or knife. It cures to give high mechanical properties typical of epoxy compounds. It is resistant to oils, greases, petroleum, salts, many acids and alkalis and most commonly met corrosive media. It does not shrink on curing, and is designed to be used when cured from 5 °C to 60 °C. Its impact resistance and mechanical strength is significantly greater than that of concrete.

  • High strength.
  • Non-slump.
  • Strong adhesion.
  • Chemical-resistant.
  • Impact-resistant.
  • Non-shrink.
  • Trowels to a smooth finish.
  • Supplied in pre-weighed units.
  • No primer required.
Product Data Sheet Show all documents

Usage

  • For surface repairs of fine cracks and spalls.
  • For gap-filling, grouting, bedding fixtures etc.
  • For repairs to arrises and edge pieces without the use of formwork.
  • Wherever a thixotropic epoxy mortar is required.
  • Repairing vertical honeycomb concrete in abutments or overhead repairs on soffits.
  • Fixing slip bricks to concrete.
  • Securing bolts into walls.
  • As a gap-filling adhesive.
  • Filling bolt pockets.
  • Bedding tiles.
  • Repairing concrete posts in situ.
 

Advantages

  • High strength.
  • Non-slump.
  • Strong adhesion.
  • Chemical-resistant.
  • Impact-resistant.
  • Non-shrink.
  • Trowels to a smooth finish.
  • Supplied in pre-weighed units.
  • No primer required.

Packaging

3 kg & 10 kg pails

Colour

Pale grey

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

CE mark under Concrete repair product for non structural repair. PC Mortar (based on Epoxy Resin) EN1504-3
Product Information

Chemical Base

2-component epoxy based mortar

Shelf Life

Use within 24 months.

Storage Conditions

Store in unopened containers in cool, dry conditions at ambient temperatures between 5 °C - 35 °C (ideally 15-20 °C).

Density

ca. 1.80 g/cm3
Technical Information

Compressive Strength

≥ 15 MPa

Tensile adhesion strength

≥ 0.8 MPa (6.4 MPa)

Thermal Compatibility

≥0.8 MPa (Part 4 dry cycling)

Chemical Resistance

Most aqueous systems, raw sewage, urine ,fresh water, sea water, diluted & concentrated alkalis, diluted acids, mineral, vegetable and animal fats & ammonia.

Water Absorption

≤0.5 kg/m2h0.5 (capillary absorption)

Application

Application Information

Layer Thickness

3 kg is sufficient to cover 1.1 m² at 1.5 mm thickness

Ambient Air Temperature

+5 °C to +40 °C

Pot Life

The pot life of this product is 1 hour / 30mins at 20 °C. Low temperatures will retard the cure. Do not apply below 4 °C.

Curing Time

Initial cure = 5 hours

Full cure = 3-5 days (@ 25 °C)
Application steps

SUBSTRATE PREPARATION

Ensure surfaces are free from flaking material, dust, rust and grease. Saw/chisel edges to a defined area to a depth of 3 mm. When applying to steel, shot blast, grind, or emery to a bright finish and remove residues.

CLEANING OF TOOLS

Clean tools etc with white spirit

Documents