Product Data Sheet Show all documents
EVERBUILD® 710 Febflor Flexiplus Latex

EVERBUILD® 710 Febflor Flexiplus Latex

SELF LEVELLING COMPOUND WITH ADDED LATEX POWDER

EVERBUILD® 710 Febflor Flexiplus Latex is a latex modified cement based powder, which when mixed with water, can be used to level out uneven floors and screeds. Typical surfaces include concrete, existing ceramic tiles, asphalt, brick, stone etc. This product is intended for use prior to laying ceramic tiles, thermoplastic tiles, lino, wood block flooring or carpet. EVERBUILD® 710 Febflor Flexiplus Latex already contains powdered latex, eliminating the need for separate expensive latex liquids. When mixed as directed, the compound provides a free flowing mix that sets in ~90 minutes and can be overlaid after only 8 hours at normal temperatures. NOTE: This product is not suitable for use as a final wearing surface.  

  • Enhanced flow properties coupled with long open time giving easy trowelling.
  • Fast setting - sets in 8 hours.
  • Up to 6 mm in depth in one coat.
  • Protein (casein) free.
  • Internal use.
Application temperature 4 °C to 35 °C Service Temperature -30 to 70 °C. Open Time 30 mins @ 20 °C Setting Time8 hours @ 20 °C
Product Data Sheet Show all documents

Usage

For levelling uneven subfloors prior to covering/tiling, without the need to use a separate latex additive.

Advantages

  • Enhanced flow properties coupled with long open time giving easy trowelling.
  • Fast setting - sets in 8 hours.
  • Up to 6 mm in depth in one coat.
  • Protein (casein) free.
  • Internal use.
Application temperature 4 °C to 35 °C Service Temperature -30 to 70 °C. Open Time 30 mins @ 20 °C Setting Time8 hours @ 20 °C

Packaging

20 kg Bag

Colour

Fine grey powder

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

Tested to EN13813 Class CT-C30-F6
Product Information

Shelf Life

9 months from date of manufacture when stored according to manufacturer’s instructions.

Storage Conditions

Store at 5-25 °C. PROTECT FROM DAMP.

Density

1.6 g/cm³ (dry) 2.3  g/cm3  (wet or cured)

Application

Application Information

Layer Thickness

Feathered edge to 6 mm
Consumption

Consumption

20 kg covers approximately 4 m2 at 3 mm (standard) depending on porosity of substrate.
Application steps

APPLICATION

20 kg of EVERBUILD® 710 Febflor Flexiplus Latex will require 4 litres of water. Always add the powder to water. This should be carried out by stepwise addition whilst stirring until a free flowing creamy compound is produced. Pour the mixture out into the prepared floor and allow it to find its own level. Trowel down lightly to achieve an overall thickness not exceeding 6 mm. Where further finishing is required, allow the surface to stiffen, usually ¾ to one hour after application, and lightly sprinkle with water and carefully trowel to produce a smooth appearance. Do not sprinkle excessive water or over trowel at this stage.

Additional layers, each not exceeding 6 mm, may be applied to achieve the required depth. Prime with Everbuild 501 PVA Bond diluted 1:3 with water between layers.

For areas where deep depressions occur, (greater than 6 mm in depth up to 25 mm) , add 1 part of clean, dry sharp sand to 1 part Self Levelling Compound. The sand should be added after mixing powder with water. It is advisable to reduce the amount of mixing water before adding sand, and then top up with water to achieve the correct consistency. Note: the flow characteristics will be affected by addition of the sand. If the product starts to stiffen or set, DO NOT try to remix or add extra water.

 

Documents