Product Data Sheet
Show all documents

Sikafloor® Marine-590

IMO approved self-levelling decorative resin

Sikafloor® Marine-590 is a self-levelling aliphatic 2-component polyurethane decorative floor resin. It is part of the Sikafloor® Marine Deco Comfort system for interior use and the Sikafloor® Marine Deco Teak system for interior and exterior use. Sikafloor® Marine-590 has been tested according to the FTP Code system and is approved according the IMO Marine Equipment Directives. If Sikafloor® Marine-590 needs to be accelerated, Sikafloor® Marine-001 or -002 can be used.  

  • Good application characteristics
  • Very UV stable (non yellowing)
  • Decorative designs solutions
  • IMO approved
  • Very low VOC emission
  • Solvent-free 
  • Long term elastic
  • Acceleration option available
 
Find a Distributor
Product Data Sheet
Show all documents

PRODUCT BENEFITS

  • Good application characteristics
  • Very UV stable (non yellowing)
  • Decorative designs solutions
  • IMO approved
  • Very low VOC emission
  • Solvent-free 
  • Long term elastic
  • Acceleration option available
 

Usage

Sikafloor® Marine-590 is designed as a part of the Sikafloor® Marine Deco systems. It is designed for mechanical resistant internal flooring in ship and boat construction and as final compound in the Sikafloor® Marine Deco system for interior and exterior use.
This product is suitable for experienced professional users only. 
Tests with actual substrates and conditions have to be performed ensuring workability, adhesion and material compatibility.  

Packaging

Sikafloor® Marine-590 (A)

Pail

15 kg

Sikafloor® Marine-590 (B)

Pail

5 kg

Sikafloor® Marine-001/002 

Bottle

0.28 kg

Product Details

Typical Product Data
Properties

Sikafloor® Marine-590 (A)

Sikafloor® Marine-590 (B)

Chemical base

Polyurethane

Isocyanate

Colour (CQP001-1)

mixed

Coloured

Transparent

Various colours available (see colour design chart)

Density

 

mixed

1.2 kg/l

1.2 kg/l

1.2 kg/l

Solid content

100 %

Mixing ratio

by weight

75 : 25

Application temperature

substrate, climate

15 ─ 30 °C A, B

Shore A hardness (CQP023-1 / ISO 48-4)

84

Tensile strength (DIN 53504)

8 MPa

Elongation at break (DIN 53504)

65 %

Pot-life

10 °C

20 °C

30 °C

120 minutes

90 minutes

45 minutes

Shelf life

9 months C

12 months C

CQP = Corporate Quality Procedure

A) substrates must be 3 °C above the dew point

B) max. 80 % r.h.C) stored in sealed container in up-right position in a dry place between 5 and 30 °C, protected from direct sunlight
Technical Information

CURE MECHANISM

The curing of Sikafloor® Marine-590 takes place by a chemical reaction of the two components.
Higher temperatures speed up and lower temperatures slow down the curing process.

CHEMICAL RESISTANCE

For advice contact the Technical Department of Sika Industry.

Application

Application Information

Surface Preparation

Sikafloor® Marine-590 is installed as a black primary deck covering and/or as floor covering in all colours.
Metallic decks need to be prepared to SA 2.5 (ISO 8501). Aluminium decks must not be shot blasted. The prepared metallic surfaces need to be clean, free of dirt, grease, oil and loose particles before the SikaCor® ZP Primer is applied. Cementitious substrates have to be mechanically prepared to remove laitance.
Clean the surface and ensure a surface moisture content of ≤ 4 % before applying Sikafloor®-150 /-151 primer.
The application area must be protected against weather and direct sunlight.
If IMO is required, get in contact with Sika to choose an appropriate combination of the Sikafloor® Marine Deco system.

Application

Sikafloor® Marine-590 is poured and spread evenly by means of a notched trowel, flat trowel or pin-rake. In critical areas a spike roller can be used to improve levelling and de-airing. For deeper sections (e.g. unevenness), it might be necessary to pre-level these sections. Ensure the pre-leveled sections have achieved "foot traffic" cure level prior to proceeding.
For liquid application on cambers and slopes multiple applications steps may be needed. Curing speed depends on temperature and layer thickness. Always consider the pot life to keep a wet edge.
Prior to application, always consult the most current Application Manual.

Curing

Indications regarding curing details see table below.

Tempera-
ture

Foot traffic

Light traffic A

Full cure

10 °C

30 hours

48 hours

6 days

20 °C

16 hours

24 hours

4 days

30 °C

12 hours

18 hours

3 days

A) food trolleys and light rolling equipment on soft wheels

Removal

Uncured Sikafloor® Marine-590 can be removed from tools and equipment with Sika® Colma Cleaner or another suitable solvent. Once cured, the material can only be removed mechanically.
Hands and exposed skin shall be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water.
Do not use solvents on skin.

Application Limits

Freshly applied Sikafloor® Marine-590 must be protected from moisture, condensation and water for at least 1 day. Uncured material reacts in contact with water (foaming).

STORAGE CONDITIONS

Both components of Sikafloor® Marine-590 have to be kept between 5 °C and 30 °C in a dry place. Do not expose it to direct sunlight. After opening of the packaging, the contents need to be protected against moisture.

Minimum temperature during transportation is 5 °C.

Documents