Product Data Sheet Show all documents

Sikafloor® Marine-599

Self-leveling decorative resin

Sikafloor® Marine-599 is a self-levelling aliphatic 2-component polyurethane decorative floor resin. It is part of the Sikafloor® Marine Deco system for exterior use.
If Sikafloor® Marine-599 needs to be accelerated, Sikafloor® Marine-001 or -002 can be used.  

  • Good application characteristics
  • Very UV stable (non yellowing)
  • Decorative designs solutions
  • Very low VOC emission
  • Solvent-free 
  • Longterm elastic
  • Acceleration option available
 
Find a Distributor
Product Data Sheet Show all documents

PRODUCT BENEFITS

  • Good application characteristics
  • Very UV stable (non yellowing)
  • Decorative designs solutions
  • Very low VOC emission
  • Solvent-free 
  • Longterm elastic
  • Acceleration option available
 

Usage

Sikafloor® Marine-599 is designed as a part of the Sikafloor® Marine Deco systems as synthetic teak decking solution for external decks in shipbuilding, cruise and leisure boat construction. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring workability, adhesion and material compatibility.  

Packaging

Sikafloor® Marine-599 (A)

Pail

15 kg

Sikafloor® Marine-599 (B)

Pail

5 kg

Sikafloor® Marine-001/002 

Bottle

0.28 kg

Product Details

Typical Product Data
Properties

Sikafloor® Marine-599 (A)

Sikafloor® Marine-599 (B)

Chemical base

Polyurethane

Isocyanate

Colour (CQP001-1)

mixed

Coloured

Transparent

Various colours available (see colour design chart)

Density

 

mixed

1.5 kg/l

1.2 kg/l

1.4 kg/l

Solid content

100 %

Mixing ratio

by weight

75 : 25

Application temperature

substrate / climate

15 ─ 30 °C A, B

Shore A hardness (CQP023-1 / ISO 48-4)

84

Tensile strength (DIN 53504)

8 MPa

Elongation at break (DIN 53504)

65 %

Pot-life

10 °C

20 °C

30 °C

120 minutes

90 minutes

45 minutes

Shelf life

9 months C

12 months C

CQP = Corporate Quality Procedure

A) substrates must be 3 °C above the dew point

B) max. 80 % r.h.C) stored in sealed container in up-right position in a dry place between 5 and 30 °C, protected from direct sunlight
Technical Information

CURE MECHANISM

The curing of Sikafloor® Marine-599 takes place by a chemical reaction of the two components.
Higher temperatures speed up and lower temperatures slow down the curing process.

CHEMICAL RESISTANCE

For advice contact the Technical Department of Sika Industry.

Application

Application Information

Surface Preparation

Sikafloor® Marine-599 is installed on top of the deck levelling compound.

Metallic decks need to be prepared to SA 2.5 (ISO 8501). Aluminum decks must not be shot blasted. The prepared metallic surfaces need to be clean, free of dirt, grease, oil and loose particles before the SikaCor® ZP Primer is applied.
The application area must be protected against weather and direct sunlight.

Application

Sikafloor® Marine-599 is poured and spread evenly by means of a notched trowel, flat trowel or pin-rake. In critical areas a spike roller can be used to improve levelling and de-airing. For deeper sections (e.g. unevenness), it might be necessary to pre-level these sections. Ensure the pre-leveled sections have achieved "foot traffic" cure level prior to proceeding.

 

For liquid application on cambers and slopes multiple applications steps may be needed. Curing speed depends on temperature and layer thickness. Always consider the pot life to keep a wet edge.
Prior to application, always consult the most current Application Manual.

Curing

Indications regarding curing details see table below.

Tempera-
ture

Foot traffic

Light traffic A

Full cure

10 °C

30 hours

48 hours

6 days

20 °C

16 hours

24 hours

4 days

30 °C

12 hours

18 hours

3 days

A) food trolleys and light rolling equipment on soft wheels

Removal

Uncured Sikafloor® Marine-599 can be removed from tools and equipment with Sika® Colma Cleaner or another suitable solvent. Once cured, the material can only be removed mechanically.
Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water.

Do not use solvents on skin.

Application Limits

Freshly applied Sikafloor® Marine-599 must be protected from moisture, condensation and water for at least 1 day. Uncured material reacts in contact with water (foaming).

STORAGE CONDITIONS

Both components of Sikafloor® Marine-599 have to be kept between 5 °C and 30 °C in a dry place. Do not expose it to direct sunlight. After opening of the packaging, the contents need to be protected against moisture.

Minimum temperature during transportation is 5 °C.

Documents