Product Data Sheet Show all documents
EVERBUILD® No Waste Expanding Foam

EVERBUILD® No Waste Expanding Foam

Polyurethane based, quick-setting, handheld expanding foam allowing part used-cans to be saved and used again

EVERBUILD® No Waste Expanding Foam is a handheld foam that allows part-used cans to be saved and used again and has a shelf life of 15 months, compared with 12 months for conventional foams. Its unique safety valve will not clog or leak.

  • Long shelf life.
  • Re-usability – canister may easily be re-used again.
  • Safer valve design - rubber-free valve gives no leaky or sticky valves.
  • Safety in transport – internal valve reduces potential of impact damage. Canister may be transported/stored in horizontal as well as vertical position.
  • Once applied, EVERBUILD® No Waste Expanding Foam expands greatly on application to 100 %-150 % of its original volume.
  • Once cured it can be cut, sawn or plastered over after only one hour.
Cell StructureMedium fineTemp Res Of Cured Bead Long Term: -40 °C to +80 °C Short Term:  -40 °C to +100 °C
Product Data Sheet Show all documents

Usage

Filling
  • Irregular gaps in stone, brick, concrete or plaster.
  • Gaps around pipe entries through walls.
  • Gaps around window frames, door frames.
  • Electrical wire chasing prior to plastering.
  • Deep joints prior to applying sealant or plaster.
Insulating             
  • Behind cladding to exterior walls.
  • Behind soffit and barge boards.
Fixing
  • Window frames.
  • Door frames.
  • Timber structures.
  • Window sills and thresholds.
 

Advantages

  • Long shelf life.
  • Re-usability – canister may easily be re-used again.
  • Safer valve design - rubber-free valve gives no leaky or sticky valves.
  • Safety in transport – internal valve reduces potential of impact damage. Canister may be transported/stored in horizontal as well as vertical position.
  • Once applied, EVERBUILD® No Waste Expanding Foam expands greatly on application to 100 %-150 % of its original volume.
  • Once cured it can be cut, sawn or plastered over after only one hour.
Cell StructureMedium fineTemp Res Of Cured Bead Long Term: -40 °C to +80 °C Short Term:  -40 °C to +100 °C

Packaging

750 ml aerosol can

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

B3 (DIN 4102, Part 1)
Product Information

Chemical Base

Polyurethane

Shelf Life

15 months in original containers at stated storage temperatures

Storage Conditions

Store upright between +20 °C and +25 °C. Pressurized container. Protect from sunlight and do not expose to temperatures above 50 °C. Store as flammable liquid.

Note: Elevated temperatures will reduce shelf life dramatically.

Density

ca. 17 kg/m3 (bulk density of foam)
Technical Information

Compressive Strength

2 N/cm2 (DIN 53421) at 10 % stress

Tensile Strength

10 N/cm2 (DIN 53430)

Elongation at break

26 %

Shear Strength

6 N/cm2 (DIN 53427)

Application

Application Information

Substrate Temperature

+5 °C to +25 °C. (Optimum 20 °C)

Cutting Time

18 - 21 mintes on a 20 mm bead

Tack Free Time

11 - 13 minutes
Consumption

Yield

100 %-150 % of its original volume following discharge

35 L (750 ml can)
Application steps

APPLICATION INSTRUCTIONS

Carefully read instructions and text in warning box before use and always wear protective equipment detailed.

SUBSTRATE PREPARATION

Ensure all surfaces are clean, sound and free from dust and loose particles. Moisten surfaces to be sealed with water. This assists the curing process.

APPLICATION

Carefully read instructions and text in warning box before use and always wear protective equipment detailed. Shake can well before use (about 20 times). Carefully fix nozzle. Do not overtighten or force. Always use can upside down. Only partially fill cavities as the foam will expand to fill the remaining space. When used for fixing door/window frames, supports must be used until the foam is fully cured, and product must be used with mechanical fixings. All information on the Technical Data Sheets for this product must be observed.

CLEANING OF TOOLS

Immediately after use, clean nozzles and valve tip with Everbuild® Dual Purpose Foam Cleaner. Any excess foam can be removed whilst still wet with Everbuild® Dual Purpose Foam Cleaner. Once cured, foam must be removed by scraping.

Documents