Sarnacol®-2142 V
VOC free adhesive for Sarnafil® felt backed roof waterproofing membranes
Sarnacol®-2142 V is a VOC free, 1-part, polyurethane based moisture curing adhesive.
- VOC free
- Adheres to solid, rough, clean, dry or slightly moist surfaces
- Application by roller
- Good adhesion to different substrates
Usage
Bonding Sarnafil® G Felt-type and Sikaplan® SGK type membranes to roof substrates. Bonding substrates:- Concrete, lightweight concrete, plaster
- Oriented fibre strand boards, plywood panels
- Fibre cement boards
- Slated/mineralized bitumen sheets; new and aged
- Mineral fibre boards: product specific approval with sufficient compressive strength and appropriate surface for bonding
- PUR/PIR insulation boards with lamination (glass or mineral fibre fleece)
- EPS insulation boards: Slap stock foaming cut, compressive strength ≥ 100 kPa
- Steel panels: product specific approval (e.g. Brucha Panels WP)
Advantages
- VOC free
- Adheres to solid, rough, clean, dry or slightly moist surfaces
- Application by roller
- Good adhesion to different substrates
Packaging
One way container: | 10 kg |
Packing unit: | Euro pallet or single container |
Refer to current price list for packaging variations
Colour
BlueProduct Details
Chemical Base
Polyurethane moisture curing
Shelf Life
12 months from date of production.
Storage Conditions
The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between + 5 °C and + 25 °C. Always refer to packaging.
Density
~1,12 kg/l (+20 °C)
Consistency
Liquid
Volatile organic compound (VOC) content
VOC-CH | 0,0 % |
VOC-EU | 0,0 % |
Compatibility
Incompatible substrates:
- Single ply waterproofing membranes (thermoplastics/elastomers)
- Sheet metal
- Talcum coated bituminous sheets
Application
Ambient Air Temperature
+5 °C min
Substrate Temperature
+5 °C min
Consumption
Consumption depends on the roughness and absorbency of the substrate.
Recommended consumption of Sarnacol®-2142 V on different substrates (+20 °C / 50 % r.h. )
Substrate | g/m2 |
Mineral-fibre board: Rockwool Bondrock MV, Multifix | 350–800 |
Bituminous sheet: New/Aged: Slated/mineral surface | 250–400 |
PUR/PIR: Type Kingspan TR 27 with glass tissue facing | 250–400 |
Timber: OSB3 | 250–400 |
EPS: Prefabricated roof insulation sheets: e.g. ISOBOUW | 250–400 |
Sandwich panel | 250–400 |
Concrete | 250–400 |
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc.
SUBSTRATE QUALITY
The substrate must offer sufficient strength and adhesion to resist the forces generated by wind suction.
SUBSTRATE PREPARATION
The substrate must be firm, clean, dry or slightly moist, free from oil, grease, dust, stripping agents, standing water, bitumen residue and loose friable particles.
APPLICATION
Reference must be made to further documentation where applicable, such as relevant method statement, application manual and installation or working instructions.
General information
Sarnacol®-2142 V must be stirred carefully before use. Keep adhesive container closed whenever adhesive is not being used to prevent surface skinning. To improve the workability of the adhesive at low temperatures, the closed container can be placed in warm water (max. +40 °C). Adhesive residue on Sarnafil® G Felt must be cleaned with Sarna Cleaner. Adhesive residue on Sarnafil® T Felt, must be cleaned with Sarnafil® T Clean.
General bonding procedure - Wet bonding
The adhesive is spread evenly onto the substrate by using a synthetic application roller directly from the container and ensuring there are no lumps in the applied layers.
Bonding to PVC Membranes
Apply adhesive onto the substrate. Do not apply the adhesive to an area greater than can be covered within 15 minutes. Do not pour out the adhesive and roll in a second stage. After a few minutes (before the adhesive forms a skin), place the felt-backed membrane in position onto the wet substrate adhesive. Press down firmly on the membrane using a suitable pressure roller such as a water-filled, or heavy steel roller 40 –50 kg.
Bonding to EPS insulation board
Apply adhesive onto the substrate in a thin layer (~250 g/m2).
Bonding to very absorbent substrates (Mineral fibre boards)
Apply 2 coats of adhesive. The first coat ~800 g/m2. Allow the adhesive to dry completely. Apply a second coat ~400 g/m2 max.
CLEANING OF TOOLS
Clean all tools and application equipment with Sarna Cleaner or Sarnafil® T immediately after use. Hardened material can only be mechanically removed.