Sikalastic® Rapid Filler Compound
Sikalastic® Rapid Filler Compound is a fast-reactive and flexible product used to fill small cracks and joints as well as to smooth out areas of minor unevenness. It is used mainly to prepare the substrate before PMMA waterproofing and surfacing systems are applied. The product can also be used to smooth out fleece overlaps in the waterproofing layer.
- Fast curing
- Easy and fast application
- Solvent free
- Hydrolysis and alkali-resistant
Usage
- Filler for small cracks and joints for prior to application of Sikalastic® Rapid systems.
Advantages
- Fast curing
- Easy and fast application
- Solvent free
- Hydrolysis and alkali-resistant
Packaging
SUMMER | |
Sikalastic® Rapid Filler Compound | 10.00kg |
Sikalastic® Rapid Catalyst | 0.30kg (3 x 0.1kg) |
Total | 10.30kg |
WINTER | |
Sikalastic® Rapid Filler Compound | 10.00kg |
Sikalastic® Rapid Catalyst | 0.60kg (6 x 0.10kg) |
Total | 10.60kg |
Please see Curing Details section for more information
Colour
Pigmented - RAL 7032 (Pebble Grey)
Product Details
Chemical Base
Two component Polymethylmethacrylate (PMMA) Resin and catalyst
Shelf Life
Unopened products have a shelf life of at least 12 months.
Storage Conditions
Store products sealed in their original airtight container and in a cool, dry and frost-free place. Direct sunlight on the containers should be avoided, including on site. After removing some of the contents, reseal the containers so they are airtight.
Reference should also be made to the storage recommendations of the material safety datasheet.
Density
1.34g/cm³
System Structure
Smoothing fleece overlaps | 0.30kg/m run |
Filling | 1.70kg/L |
Application
Ambient Air Temperature
-5°C min / + 35°C max
Relative Air Humidity
The relative humidity must be ≤90%Substrate Temperature
+3°C min / + 50°C max
Dew Point
Beware of condensation. Surface temperature during application and cure must be a minimum of 3°C above dew point.
The substrate temperature must not be less than +3°C if a topping is applied to the surface. Reaction problems can occur at lower temperatures.
Substrate Moisture Content
The surface to be coated must be dry and ice-free
The surface must be protected from moisture until the coating has hardened
Substrate Pre-Treatment
Apply the surfacer to the hardened Sikalastic® Rapid Primer
Pot Life
The material in opened containers should be applied immediately.
At 20°C, 2% catalyst the pot life is approximately 15 minutes
Applied Product Ready for Use
Temperature | Catalyst | Rain resistant | Can be trafficked/overcoated | Full cure |
20°C | 2% | 30 minutes | 45 minutes | 3 hours |
Note: Times are approximate and will be affected by changing ambient conditions.
Higher temperatures or greater proportions of Sikalastic® Rapid Catalyst will reduce reaction times, while lower temperatures and smaller proportions of Catalyst will increase reaction times.
The following table indicates the recommended amount of Sikalastic® Rapid Catalyst required to adjust the curing reaction to the temperature.
Substrate temperature in °C; required amounts of Sikalastic® Rapid Catalyst in % w/w (guide)
-10 | -5 | +3 | 5 | 10 |
- | - | 4% | 4% | 4% |
15 | 20 | 25 | 30 | 35 |
2% | 2% | 2% | 2% | 2% |
40 | 45 | 50 | ||
1% | 1% | 1% |
Return-to-service times are provided as a guide only and may vary as a result of conditions. Newly installed balconies should be protected from exposure to heavy traffic by overlaying with an appropriate protective covering. This is particularly critical where early access is needed by other construction related traffic. Sika Liquid Plastics will not be held responsible for damage to balcony surfaces that results from failures to adequately protect newly laid areas.
For further advice, consult Sika Liquid Plastics Technical Customer Services
MIXING
Use a twin-paddle stirrer to mix the product.
First stir the tub contents thoroughly.
Then add the Sikalastic® Rapid Catalyst while stirring the resin at the slow speed setting and mix for 2 minutes. Make sure that the product on the base and sides of the container is mixed in.
At product temperatures <10°C the product should be stirred for 4 minutes,as the catalyst will take longer to dissolve.
APPLICATION
Fill in small cracks or joints using a pointing trowel or finishing trowel. Use the pointing trowel to smooth over minor differences in height.
Preparation for subsequent layers - None required.
Refer to Sikalastic® Rapid Method Statement for more information.
CLEANING OF TOOLS
If work is interrupted or when it is completed, clean the tools thoroughly with Sikalastic® Rapid Cleaner within the pot life of the material (approx. 10 minutes). This can be done with a brush. Do not use the tools again until the Cleaner has evaporated fully.
Simply immersing the tools in the Cleaner will not prevent the material hardening.