Product Data Sheet Show all documents
SikaFiber® Novocon® HE1060-HT

SikaFiber® Novocon® HE1060-HT

High Tensile Steel Fibres For Concrete

SikaFiber® Novocon® HE1060-HT steel fibres are designed specifically for the reinforcement of concrete, mortars and other cementitious mixes. SikaFiber® Novocon® HE1060-HT is a cold drawn wire fibre, deformed with hooked ends to provide optimum performance within the concrete mix.

  • Provides uniform multi-directional concrete reinforcement
  • Increases crack resistance, ductility, energy absorption or toughness of concrete
  • Improves impact resistance, fatigue endurance and shear strength of concrete
  • High tensile strength fibre bridging joints and cracks to provide tighter aggregate interlock resulting in increased load carrying capacity
  • Provides increased ultimate load bearing capacity which allows possible reduction of concrete section
  • Requires less labour to incorporate into concrete than conventional reinforcement
  • Offers economical concrete reinforcement solutions with greater project scheduling accuracy
  • Ideally suited for hand or vibratory screeds, laser screeds and all conventional finishing equipment
Product Data Sheet Show all documents

Usage

  • Ground supported slabs
  • Suspended Floors
  • Jointless floors
  • External roads & pavements
  • Precast
  • Overlays
  • Walls
  • Blast-resistant concrete
 

Advantages

  • Provides uniform multi-directional concrete reinforcement
  • Increases crack resistance, ductility, energy absorption or toughness of concrete
  • Improves impact resistance, fatigue endurance and shear strength of concrete
  • High tensile strength fibre bridging joints and cracks to provide tighter aggregate interlock resulting in increased load carrying capacity
  • Provides increased ultimate load bearing capacity which allows possible reduction of concrete section
  • Requires less labour to incorporate into concrete than conventional reinforcement
  • Offers economical concrete reinforcement solutions with greater project scheduling accuracy
  • Ideally suited for hand or vibratory screeds, laser screeds and all conventional finishing equipment

Packaging

25 kg bags

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

Conforms to the requirements of BS EN 14889-1:2006, Group I
DoP 29544041, certified by Factory Production Control Body 1397 and provided with the CE mark
Product Information

Chemical Base

Bright and clean wire (hooked end)

Shelf Life

24 months from date of production

Storage Conditions

The pallets should be protected against rain and snow. Do NOT stack pallets on top of each other.

Dimensions

Fibre Length

Equivalent Diameter

Aspect Ratio

60mm

1.0mm

60

 
Technical Information

Specific Advice

It is recommended that gloves and eye protection be used when handling or adding SikaFiber® Novocon® HE1060-HT steel fibres to concrete.

Tensile Strength

1550 N/mm2

Application

Application Information

Compatibility

SikaFiber® Novocon® HE1060-HT steel fibres are compatible with all curing compounds, superplasticisers, water reducers, hardeners and coatings.
Consumption

Recommended Dosage

Typical dosage 20 - 40 kg/m3. Sika technical staff can offer advice on dosage once performance requir
Application steps

APPLICATION INSTRUCTIONS

MIXING

SikaFiber® Novocon® HE1060-HT steel fibres can be added during or after the batching of the concrete but should never be added as the first component. The concrete should be mixed for sufficient time (minimum 5 minutes at full mixing speed) to ensure uniform distribution of the fibres throughout the concrete.

APPLICATION

SikaFiber® Novocon® HE1060-HT steel fibres can be pumped and placed using conventional equipment.

Conventional finishing techniques and equipment can be used when finishing SikaFiber® Novocon® HE1060-HT steel fibre concrete. In some cases an extra bull float process is advised and lowering the angle of the power float blades will help to minimize fibre exposure on the surface.

 

Documents