Product Data Sheet Safety Data Sheet Show all documents
Sikafloor® ProSeal W

Sikafloor® ProSeal W

Water dispersed curing and sealing compound for concrete floors

Sikafloor® ProSeal W is a one part water dispersed acrylic emulsion to cure, harden and seal fresh or hardened concrete.

  • Water dispersion
  • Suitable for indoor use where solvent-based products cannot be applied because of health and safety regulations
  • Helps control dusting for both new and existing concrete floor surfaces
  • Effectively cures and seals concrete surfaces in a single, economic operation
  • Curing Efficiency to ASTM C-156 is 75%
  • Very low yellowing
  • Easy application by spray or roller
Product Data Sheet Safety Data Sheet Show all documents

Usage

Sikafloor® ProSeal W is used for optimum curing and sealing of fresh concrete floors and structures.
  • Curing compound in order to limit surface drying and cracking
  • Provides curing and sealing for Sikafloor® dry shake hardeners
  • Anti-dust treatment and improvement of the abrasion resistance of existing concrete surfaces
  • Suitable for exterior and interior application
 

Advantages

  • Water dispersion
  • Suitable for indoor use where solvent-based products cannot be applied because of health and safety regulations
  • Helps control dusting for both new and existing concrete floor surfaces
  • Effectively cures and seals concrete surfaces in a single, economic operation
  • Curing Efficiency to ASTM C-156 is 75%
  • Very low yellowing
  • Easy application by spray or roller

Packaging

25 l cans and 200 l drums

Colour

White liquid, clear when cured.

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

Tested for water retention according to ASTM C-156 for curing liquids type 1, class
Conforms to the requirements of EN 13813 SR - B 1.5.

Epoxy textured roller and seal coat according to EN 13813:2002, DoP 02 08 03 04 005 0 000003 1029 and provided with the CE-mark
Product Information

Chemical Base

Water dispersed acrylic emulsion.

Shelf Life

12 months from date of production

Storage Conditions

stored properly in original, unopened and undamaged sealed containers, in dry conditions at temperatures between +5 °C and +30 °C. Protect from frost.

Density

~1.0 kg/I (at +20 °C)

Solid content by weight

~16 %

 

Application

Application Information

Ambient Air Temperature

+10 °C min. / +30 °C max.

Relative Air Humidity

 80 % max.

Dew Point

Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.

Substrate Temperature

+10 °C min. / +30 °C max.

Curing Time

Substrate temperature

Foot traffic

Full cure

+10 °C

~16 hours

~24 hours

+20 °C

~8 hours

~20 hours

+30 °C

~6 hours

~16 hours

Full cure times are approximate and will be affected by changing substrate and ambient conditions

Waiting Time / Overcoating

Allow previous coats to become tack free before applying additional coats.

Substrate temperature

Time

+10 °C

~90 minutes

+20 °C

~45 minutes

+30 °C~40 minutes

Times are approximate and will be affected by changing substrate and ambient conditions, particularly temperature and relative humidity.
Consumption

Consumption

0.1–0.2 l/m2/coat
Requirements of relevant local standards and guidelines apply.
This figure is theoretical and does not include for any additional material required due to surface porosity, surface profile, variations in level and wastage, etc.
Application steps

MIXING

Sikafloor® ProSeal W is supplied ready for use. Stir thoroughly with an electric stirrer with low speed (~300 rpm) for 2 minutes before use.

APPLICATION

For fresh concrete, apply immediately after finishing techniques have been completed.

For dry shaked topped concrete, apply immediatelty after completion of the power floating operation
Apply in a continuous even film by low-pressure spray unit. The suitability of spraying equipment must be confirmed by trials.
Application also possible by brush or roller.
To achieve the highest visual aesthetics and performance, a second coat is recommended.
Wait for first coat to dry tack free before applying a second coat. (see waiting time / overcoating)

CLEANING OF TOOLS

Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be removed mechanically.

CLEANING

To maintain the appearance of the floor after application, Sikafloor® ProSeal W must have all spillages removed immediately and must be regularly cleaned using rotary brushes, mechanical scrubbers, scrubber dryers, high pressure washers, wash and vacuum techniques, etc., using suitable detergents and waxes.

Documents