Sikafloor® MultiDur ES-47 ECF
Sikafloor® MultiDur ES-47 ECF is an epoxy based, smooth finish, electrostatically conductive flooring system. The System is designed to dissipate electrostatic charges in areas of high explosion risk.
- Thickness ~1,5–2,0 mm
- Electrostatic conductive
- Chemical resistant top layer
- Good mechanical resistance
- Easy to clean
- Waterproof
- Wearing layer available in various colours
- Smooth gloss surface finish
- Conforms to the requirements of VDE 100-610
System Structure
Usage
Industrial resin flooring on cementitious substrates for:- Medium up to heavy wear
- Flooring that needs to comply with the requirements of the standard VDE 100-600
- Automotive production plants
- Chemical production plants
- Laboratories
- Fireworks factories
- Pharmaceutical production areas
- Fibre and textile production
- Explosive storage and handling areas
- Explosive dust environments
- Aircraft maintenance hangars
- Workshops
- Battery-charging rooms
- Interior use only
Advantages
- Thickness ~1,5–2,0 mm
- Electrostatic conductive
- Chemical resistant top layer
- Good mechanical resistance
- Easy to clean
- Waterproof
- Wearing layer available in various colours
- Smooth gloss surface finish
- Conforms to the requirements of VDE 100-610
Colour
Conductive wearing layer available in many colours.
Applied colours selected from colour charts will be approximate.
Colour deviations may occur due to carbon fibre filaments.
For colour matching: Apply colour sample and confirm selected colour under real lighting conditions.
When product is exposed to direct sunlight, there may be some discolouration and colour variation, this has no influence on the function and performance of the floor finish.
Appearance
Smooth gloss finish
System Details
APPROVALS / STANDARDS
- CE Marking and Declaration of Performance to EN 1504-2 - Surface protection product for concrete - Coating.
- CE Marking and Declaration of Performance to EN 13813 - Resin screed material for internal use in buildings.
- Insulation Resistance DIN VDE 0100-600, Sikafloor® MultiDur ES-47 ECF, kiwa, Test report No. P 12174-4-E.
System Structure
Sikafloor® MultiDur ES-47 ECF (~1,5–2,0 mm)
| Layer | Product |
| 1. Primer | Sikafloor®-150/-151 |
| 2. Conductive Primer & Earthing Connection | Sikafloor®-221 W Conductive + Sika® Earthing Kit |
| 3. Conductive Wearing Layer | Sikafloor®-262 AS N |
The system structure layers as described in table must not be changed.
Composition
Epoxy
Nominal thickness
~1,5–2,0 mm
Volatile organic compound (VOC) content
Sikafloor®-262 AS N, is the finishing layer of the Sikafloor® MultiDur ES-47 ECF System. It has been awarded the Frauenhofer IPA CSM Certicate of Qualification (report number SI 1412-740). Outgassing tests were performed in accordance with CSM procedures. TVOC: ISO-AMC Class -8.0 (see ISO 14644-8). It fulfils the stringent AgBB demands for indoor air quality and low VOC emissions (refer to test report no. 392-2014-00286901A).
Compressive Strength
| ~80 N/mm² (resin filled) | (28 days / +23 °C) |
Tensile Strength
| ~40 N/mm² (resin filled) | (28 days / +23 °C) |
Chemical Resistance
Resistant to many chemicals. Contact Sika® Technical Services for additional information.
Thermal Resistance
| Exposure* | Dry heat |
| Permanent | +50 °C |
| Short-term (maximum 7 days) | +80 °C |
Short-term moist / wet heat* up to +80 °C where exposure is temporary (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
USGBC LEED Rating
Sikafloor®-262 AS N conforms to the requirements of LEED EQ Credit 4.2: Low-Emitting Materials: Paints & Coatings SCAQMD Method 304-91 VOC Content < 100 g/l.
Electrostatic Behaviour
| Resistance to Ground1 | Rg < 109 Ω |
| Typical Average Resistance to Ground2 | Rg < ~ 105 - 106Ω |
1 In accordance with IEC 61340-5-1 and ANSI/ESD S20.20.
2 Readings may vary, depending on ambient conditions (i.e. temperature, humidity) and measurement equipment.
Application
Product Temperature
+10 °C minimum / +30 °C maximum
Ambient Air Temperature
+10 °C minimum / +30 °C maximum
Relative Air Humidity
80 % maximum
Dew Point
Beware of condensation. The substrate and uncured applied floor materials must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the surface of the applied product.
Substrate Temperature
+10 °C minimum / +30 °C maximum
Substrate Moisture Content
≤4 % parts by weight. The following test methods can be used: Sika®-Tramex Meter, CM-measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Waiting Time / Overcoating
Before applying Sikafloor®-221 W Conductive on Sikafloor®-156/160/161 allow:
| Substrate Temperature | Minimum | Maximum |
| +10 °C | 24 hours | 4 days |
| +20 °C | 12 hours | 2 days |
| +30 °C | 8 hours | 1 days |
Before applying Sikafloor®-262 AS N on Sikafloor®-221 W Conductive allow:
| Substrate Temperature | Minimum | Maximum |
| +10 °C | 26 hours | 7 days |
| +20 °C | 17 hours | 6 days |
| +30 °C | 12 hours | 4 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
| Temperature | Foot Traffic | Light Traffic | Full Cure |
| +10 °C | ~30 hours | ~5 days | ~10 days |
| +20 °C | ~24 hours | ~3 days | ~7 days |
| +30 °C | ~16 hours | ~2 days | ~5 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Consumption
| Coating | Product | Consumption |
| 1. Primer | Sikafloor®-150/-151 | 1–2 × ~0,3–0,5 kg/m² |
| Levelling (if required) | Sikafloor®-150/-151 Levelling Mortar | Refer to PDS of Sikafloor®-150/-151 |
| 2. Conductive Primer & Earthing Connection | Sikafloor®-221 W Conductive Sika® Earthing Kit | 1 × 0,08–0,10 kg/m² 1 earthing point per ~200–300 m². 2 per room minimum |
| 3. Self-smoothing Wearing Layer for High Aesthetical Finish ~1,5 mm thickness | Sikafloor®-262 AS N filled with Sikafloor® Filler 1*1 | Maximum 2,5 kg/m² Binder + Sikafloor® Filler 1. Filled: 0,1–0,2 parts by weight |
| Self-smoothing Wearing Layer ~1,5 mm thickness | Sikafloor®-262 AS N filled with quartz sand F34*1 | Maximum 2,5 kg/m² Binder + quartz sand F 34. Filled: 0,1–0,3 parts by weight |
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc.
*1 All values have been determined using quartz sand F 34 (0,1–0,3 mm) from Quarzwerke GmbH Frechen and Sikafloor® Filler 1. Other quartz sand types will have an effect on the product, such as filling grade, levelling properties and aesthetics. Depending on the air temperature, the filling grade varies, generally, the lower the temperature the less the filling grade.
CLEANING
Refer to Method Statement: Sikafloor®-Cleaning Regime.