Parex® MONOGRIS E
A grey base coat/finishing coat and preparatory key coat render for variable and / or high or low suction substrates.
- Suitable for diesel and electric spray machines
- Excellent adhesion properties
- Semi-lightweight render suitable for multiple substrates
Usage
A high performance polymer modified, weather resistant, grey base coat and finishing render for vertical external and internal walls. Suitable for equalising suction on mixed substrates and as a bonding base coat on to high or low suction substrates.Suitable as a grey coat finishing render or as a base coat for receiving a Parex decorative finish. e.g. MONOREX GM & GF, MONOBLANCO, REVLANE, CRYLANE.
Advantages
- Suitable for diesel and electric spray machines
- Excellent adhesion properties
- Semi-lightweight render suitable for multiple substrates
Packaging
25 kg bags
Product Details
Composition
Hydraulic mortar containing:
Cement, lime, siliceous and calcareous sands, mineral pigments and specific admixtures.
Shelf life
12 Months from date of manufacture
Storage conditions
Dry frost free conditions
Grain size distribution
Granulometry: 0 - 1.6 mm
Compressive strength
CS II
Capillary absorption
W2
Reaction to fire
A1
Application
Mixing ratio
5.4-6.3 L per 25 kg bag
Consumption
COVERAGE
Coverage is provided as guidance only, excludes wastage and will vary subject to substrate conditions and thickness applied.
Approx 1.25 - 1.3 m2 @ 15 mm/25 kg bag
Approx 6.7 m2 @ 2 - 3 mm/25kg bag
EQUIPMENT
EQUIPMENT REQUIRED
| Application by machine | Spray Render Machine | Constant Mix and Pump Machine |
| Pump Pressure | 10-12 bar (water) | 2.5-6 bar/360 water flow L/hr |
| Pumping distance/height | Up to 120 m/60 m approx | Up to 50 m/30 m approx |
| Power Source | Diesel | Electric |
APPLICATION
- Refer to Substrate Preparation first
SUITABLE FOR
- Machine or manual applications
KEY COAT APPLICATION
- Spray apply a stippled 2-3 mm layer leaving a well textured stippled surface.
- Hand apply a 2-3 mm thick layer to the substrate and using a toothed trowel or a heavy duty and well laiden roller, texture the surface to leave a combed effect or stippled finish respectively.
- Ensure the product is mixed correctly with the correct water content and do not allow the render to cure too quickly as surface holes in the render could occur.
- Avoid applying large areas of the key coat before creating the stippled or toothed trowel finish when applying by hand.
TO RECEIVE A ONE-COAT FINISHING COAT E.G. MONOREX, MONOBLANCO, ETC
- Spray or hand apply, leaving a ruled, level toothed trowel finished minimum thickness of 6 - 8 mm.
TO RECEIVE A PAINT COATING E.G. DPR COATING OR DPR/REVLANE+ COATINGS:
- Spray or hand apply a ruled and level 7 - 8 mm base coat and leave with a toothed trowel finish. When the base coat has dried, apply a second layer of 7 - 8 mm thickness and trowel and level smooth.
- The covering thickness must be a minimum of 15mm at all points.
MONOGRIS E can be left as a finished coat though evenness of colour is not guaranteed.
|
** Ensure aircrete blocks are fully dry
before applying MONOGRIS E as block shrinkage could occur and this may crack the render if applied on a wet substrate.
MAXIMUM THICKNESS OF MONOGRIS E
| ULTRA-LIGHTWEIGHT, LIGHTWEIGHT & DENSE AGGREGATE CONCRETE BLOCKS, CLAY BLOCKS, BRICKS | STANDARD LOW AND NORMAL DENSITY LIGHTWEIGHT AIRCRETE BLOCKS | SHUTTERED CONCRETE |
| 25 mm | 20 mm | 15 mm |