Sikafloor® MultiDur ET-20
Epoxy coloured textured fast curing floor coating system
Sikafloor® MultiDur ET-20 is a 2-part, epoxy, coloured, fast curing resin based floor coating system. It provides a hard wearing, seamless, low maintenance slightly textured gloss finish. For medium - heavy wear conditions. Thickness ~1.0 mm. Internal use.
- Fast curing
- Blushing resistant
- Low odour
- Low VOC
- Improved yellowing resistance
- Seamless and hygienic
- Good chemical and mechanical resistance
- Easy application
- Low maintenance
- Seamless
- Waterproof
- Slightly textured gloss finish
- Easy cleanability
System Structure
Usage
- On concrete and cementitious screeds with normal up to medium heavy wear e.g. storage and assembly halls, maintenance workshops, garages and loading ramps
- Multi-storey and underground car parks, maintenance hangars and wet process areas, e.g. beverage and food industry
- Floors where slip resistance and easy cleanability is required
Advantages
- Fast curing
- Blushing resistant
- Low odour
- Low VOC
- Improved yellowing resistance
- Seamless and hygienic
- Good chemical and mechanical resistance
- Easy application
- Low maintenance
- Seamless
- Waterproof
- Slightly textured gloss finish
- Easy cleanability
Packaging
Refer to the individual Product Data Sheet
Colour
Available in many colours
Appearance
Textured, gloss finish
System Details
ENVIRONMENTAL INFORMATION
- Conformity with LEED v4 EQc 2: Low-Emitting Materials - Sikafloor®-150, Sikafloor®-151.
APPROVALS / STANDARDS
- CE Marking and Declaration of Performance to EN 1504-2 - Surface protection product for concrete - Coating
- CE Marking and Declaration of Performance to EN 13813 - Resin screed material for internal use in buildings
- Fire Classification EN 13501-1, Sikafloor® MultiDur ET-20, OFI Technologie & Innovation GmbH, Classification report No. 1901242-4
- Fire Testing EN ISO 11925-2, Sikafloor® MultiDur ET-20, OFI Technologie & Innovation GmbH, Test report No. 1901242/8
- Fire Testing EN ISO 9239-1, Sikafloor® MultiDur ET-20, OFI Technologie & Innovation GmbH, Test report No. 1901242/7
System Structure
Sikafloor® MultiDur ET-20 ( ~1.0 mm)
| Layer | Product |
| 1. Primer | Sikafloor®-150/-151 |
| 2. Base Coat | 1 × Sikafloor®-2640 |
| 3. Top Coat | 1 × Sikafloor®-2640 |
Composition
Epoxy
Nominal Thickness
~1.0 mm
Shelf Life
Refer to the individual Product Data Sheet
Storage Conditions
Refer to the individual Product Data Sheet
Shore D Hardness
| ~78 (7 days / +23 °C) | (DIN 53 505) |
Abrasion Resistance
| ~935 mg (H22/1000/1000) (7 days / +23 °C) | (Standard) |
Tensile Adhesion Strength
| > 1.5 N/mm² (failure in concrete) | (ISO 4624) |
Chemical Resistance
Resistant to many chemicals. Contact Sika Technical Service for specific information.
Application
Product Temperature
+10 °C min. / +30 °C max.
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
80 % max.
Dew Point
Beware of condensation
The substrate and uncured applied floor material must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the surface of the applied product.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
≤ 4 % parts by weight
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Waiting Time / Overcoating
Before applying Sikafloor®-2640 on Sikafloor®-150/-151 allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 24 hours | 3 days |
| +20 °C | 12 hours | 2 days |
| +30 °C | 8 hours | 1 day |
Before applying Sikafloor®-2640 on Sikafloor®-2640 allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 12 hours | 3 days |
| +20 °C | 6 hours | 2 days |
| +30 °C | 3 hours | 1 day |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
| Temperature | Foot traffic | Light traffic | Full cure |
| +10 °C | ~12 hours | ~15 hours | ~24 hours |
| +20 °C | ~6 hours | ~11 hours | ~14 hours |
| +30 °C | ~3 hours | ~9 hours | ~12 hours |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Consumption
Sikafloor® MultiDur ET-20 ( ~1.0 mm)
| Layer | Product | Consumption |
| 1.Primer | 1 × Sikafloor®-150/ -151 | ~0,3–0,5 kg/m² |
| 2.Base Coat | 1 × Sikafloor®-2640 | ~0,3–0,4 kg/m² |
| 3.Top Coat | 1 × Sikafloor®-2640 | ~0,4–0,5 kg/m² |
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level and wastage etc.
CLEANING
Refer to Sika® Information Manual: Sikafloor®-Cleaning Regime