Sika® Ucrete® IF
Sika® Ucrete® IF is a very heavy-duty resin floor which provides an extremely tough surface. It uses specially treated iron aggregates to provide protection against severe abrasion and mechanical exposure.
- Expert installation by fully trained and licensed applicators
- Suitable for application on to 7-day-old concrete and 3-day-old polymer screed
- Fully serviceable within 24 hours
- Very good mechanical resistance
- Very good impact resistance
- Very good abrasion resistance
- Fast installation
- Non-tainting from the end of mixing
- Good slip resistance
- Low maintenance
- Low VOC emissions
Usage
Sika® Ucrete® IF is used as a wearing layer screed for Sika® Ucrete® flooring systems. Sika® Ucrete® IF is used within wet and dry process areas including the following application areas:- Waste transfer stations
- Heavy engineering workshops
- Heavy process areas
- Storage bunkers
- Loading docks
- In front of industrial ovens
- Heavy equipment maintenance facilities
- The Product may only be used by experienced professionals.
Advantages
- Expert installation by fully trained and licensed applicators
- Suitable for application on to 7-day-old concrete and 3-day-old polymer screed
- Fully serviceable within 24 hours
- Very good mechanical resistance
- Very good impact resistance
- Very good abrasion resistance
- Fast installation
- Non-tainting from the end of mixing
- Good slip resistance
- Low maintenance
- Low VOC emissions
Packaging
Refer to the current price list for available packaging variations.
Colour
Cured colour | Red, Yellow, Green, Orange, Grey, Blue, Green/Brown. |
Product Details
APPROVALS / STANDARDS
Halal Certification Europe (HCE), Sika® Ucrete®, WHFC, Certificate No. 21453-2/1/1/Y1
Indoor Air Comfort Gold EN 16516, Sika® Ucrete®, eurofins, Certificate No. IACG-321-01-01-2023
Chemical Base
Water-based polyurethane cement hybrid
Shelf Life
Always refer to the best-before date of the individual packaging.
Storage Conditions
The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to the packaging.
Refer to the current Safety Data Sheet for information on safe handling and storage.
Density
Mixed Product | ~2.80 kg/l |
System Structure
Sika® Ucrete® IF
Layer | Product |
Primer | Sika® Ucrete® PSC |
Wearing layer | Sika® Ucrete® IF |
Compressive Strength
Cured 28 days at +23 °C | 60 N/mm² |
Modulus of Elasticity in Compression
3350 MPa | (EN 12447) |
Flexural Strength
Cured 28 days at +23 °C | 17 N/mm² |
Tensile Strength
Cured for 28 days at +20 °C | 8 MPa |
Tensile adhesion strength
> 2.0 N/mm² (concrete failure) | (EN 1542) |
Skid / Slip Resistance
PTV, slider 96 | 40–45 wet conditions |
Class | R 11 |
Service Temperature
Thickness | Minimum | Maximum | Occasional spillage |
9 mm | -40 °C | +120 °C | - |
12 mm | -40 °C | +130 °C | +150 °C |
Water permeability
Sika® Ucrete® IF exhibits zero absorption when tested to CP.BM2/67/2.
Chemical Resistance
Laboratory-defined resistance to many individual chemicals. Before proceeding, contact Sika Technical Service for specific information.
Reaction to Fire
Class Bfl-s1 | (EN 13501-1) |
Application
Layer Thickness
~9–12 mm
Product Temperature
Maximum | +30 °C |
Minimum | +10 °C |
Ambient Air Temperature
Maximum | +35 °C |
Minimum | +5 °C |
Substrate Temperature
Maximum | +30 °C |
Minimum | +5 °C |
Curing Time
Substrate temperature | Return to traffic |
+8 °C | < 24 hours |
+10 °C | 4 hours (with Sika® Ucrete® Accelerator) |
Note: Times are approximate and will be affected by changing ambient and substrate conditions.
Consumption
Layer | Product | Consumption |
Primer | Sika® Ucrete® PSC | 0.2–0.4 kg/m2 |
Wearing layer | Sika® Ucrete® IF | 28–30 kg/m2 for 9 mm 37–39 kg/m2 for 12 mm |
Note: Consumption data is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply the Product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.
SUBSTRATE PREPARATION
IMPORTANT
Reduced service life due to incorrect treatment of cracks
The incorrect assessment and treatment of cracks may lead to a reduced service life and reflective cracking.
- For static cracks, ensure the width is suitable for overcoating with Sika® Ucrete® IF.
- For dynamic cracks, ensure the movement is within the movement capacity of Sika® Ucrete® IF.
TREATMENT OF JOINTS AND CRACKS
Construction joints and existing static surface cracks in substrate require pre-treating before full layer application. Use Sikadur® or Sikafloor® resins.
The System can be applied on green or damp concrete with no standing water. Allow for at least 3 days for early concrete shrinkage to occur to prevent shrinkage cracks from appearing on the wearing surface.
Cementitious substrates must be structurally sound and of sufficient compressive strength (minimum 30 N/mm2) with a minimum tensile strength of 1.5 N/mm2.
Substrates must be clean, dry and free of contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.
APPLICATION
Application must be undertaken by a fully trained and licensed Sika® Ucrete® applicator.