Parex 100 Newton Grout
Parex 100 Newton Grout is a one-part, ultra-high strength cementitious grout. The mix design includes special shrinkage compensating components, which give a non-shrink grout in both the plastic and hardened states. Powerful plasticising agents produce a highly flowing grout at low water content.
- Easy to use.
- One-component - just add water.
- Ultra-high strength.
- Shrinkage compensated.
- Very high strength gain after 24 hours.
- Low water content.
- Good freeze thaw stability.
- Resistant to sea water.
- Can be safely used in contact with steel.
Usage
- Ultra-high strength grout and support systems for:
- Stanchion bases.
- Securing base plates.
- Vibrating machinery bed plates.
- Precast concrete units.
- Ground anchors.
- Fixing anchors, dowels, bars, rods, etc.
- Bridge bearing seats.
- Support of tanks, silos, etc.
- Applications requiring precision alignment.
Advantages
- Easy to use.
- One-component - just add water.
- Ultra-high strength.
- Shrinkage compensated.
- Very high strength gain after 24 hours.
- Low water content.
- Good freeze thaw stability.
- Resistant to sea water.
- Can be safely used in contact with steel.
Packaging
25 kg bags and 1000 kg bulk bags
Colour
Cement Grey
Product Details
CERTIFICATES AND TEST REPORTS
Parex 100 Newton Grout has been tested in accordance with the appropriate parts of the following standards:
- EN 12390, EN 196 and EN 1015.
- CRD C621: Corps of Engineers Specification for Non-Shrink Grout.
Composition
Cements, high quality aggregates and synergistic admixtures.
Shelf life
6 Months
Storage conditions
Store properly in dry conditions in undamaged and unopened original sealed packaging
Maximum grain size
Dmax: 1.0 mm
Density
~2200 kg/m3
Compressive strength
| Age | Strength |
| 24 hours | ~50 N/mm² |
| 3 days | ~70 N/mm² |
| 7 days | ~85 N/mm² |
| 28 days | ~100 N/mm² |
*Typical grout properties at 20°C with a water addition at 18% water to powder.
| Age | Strength |
| 24 hours | ~30 N/mm² |
| 3 days | ~50 N/mm² |
| 7 days | ~75 N/mm² |
| 28 days | ~90 N/mm² |
*Typical grout properties at 5°C with a water addition at 18% water to powder.
Modulus of elasticity in compression
31.8 kN/mm2
Flexural-strength
| Age | Strength |
| 24 hours | ~6 N/mm² |
| 3 days | ~7 N/mm² |
| 7 days | ~9 N/mm² |
| 28 days | ~10 N/mm² |
*Typical grout properties at 20°C with a water addition at 18% water to powder.
| Age | Strength |
| 24 hours | ~4 N/mm² |
| 3 days | ~5 N/mm² |
| 7 days | ~8 N/mm² |
| 28 days | ~10 N/mm² |
*Typical grout properties at 5°C with a water addition at 18% water to powder.
Tensile strength
| Age | Strength |
| 24 hours | ~4 N/mm² |
| 3 days | ~6 N/mm² |
| 7 days | ~8 N/mm² |
| 28 days | ~9 N/mm² |
*Typical grout properties at 20°C with a water addition at 18% water to powder.
| Age | Strength |
| 24 hours | ~4 N/mm2 |
| 3 days | ~6 N/mm2 |
| 7 days | ~8 N/mm2 |
| 28 days | ~9 N/mm2 |
*Typical grout properties at 5°C with a water addition at 18% water to powder.
Application
Mixing ratio
Water : mortar powder = 1 : 5.55 parts by weight (4.5 litres of water per 25kg bag, or 180 litres per one tonne bag).
Layer thickness
10 mm minimum / 100 mm maximum
Ambient air temperature
5°C minimum / 35°C maximum
Substrate temperature
5°C minimum / 35°C maximum
Pot Life
Up to 60 minutes if kept mobile after mixing.
Setting time
~300 minutes at 20ºC
Initial set time
~220 minutes at 20ºC
Consumption
Depends on the substrate roughness and thickness of layer applied. As a guide, one 25kg bag yields approximately 12.5 litres of mortar.
Yield
1.0kg of Parex 100 Newton Grout will yield approximately 0.5 litres of mixed grout at the recommended water addition.
1 tonne of Parex 100 Newton Grout will yield approximately 0.52 m³ of mixed grout at the recommended water addition.
The yield per 25kg of Parex 100 Newton Grout is approximately 12.5 litres.
MIXING
Pour the required quantity of clean water (4.5 litres per 25 kg bag, or 180 litres per one tonne) into the mixing vessel for each complete unit of Parex 100 Newton Grout to be used. Slowly add the powder to the water whilst continually mixing. Mechanical mixing should be carried out using either a high torque slow speed drill with a grout stirrer, or a grout mixer set on slow speed for small mixes. For larger mixes, use forced action type mixers (high speed or colloidal mixing may cause thixotropy leading to loss of flow). This material is not suitable for mixing by hand. It is of upmost importance that the product is mixed thoroughly enough that a grout consistency is obtained without the addition of further water (at least 3 minutes). Fresh grout should be allowed to stand until the air entrapped by mixing has been released.
APPLICATION
Grout should be placed within 10 minutes of mixing, or 60 minutes if kept mobile prior to placing. Continuous placing is important, pouring or pumping from one side of the form until the grout appears at the opposite side of the grouting area. Do not disturb once grouting has been completed. Parex 100 Newton Grout may be placed at temperatures between 5°C and 35°C.
For placing at temperatures outside this range, contact Sika® Technical Services Department for advice.
CURING TREATMENT
After the grout has initially hardened, remove formwork and trim edges while concrete is ‘green’.
Protect the fresh material from premature drying using an approved curing method (e.g. curing compound such as Sikafloor® ProSeal, moist geo-textile membrane, hessian, polythene sheet, etc.). In cold weather, apply heat blankets to maintain a constant temperature.
Placed grout, which is exposed, should be cured in accordance with good concrete practice.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.