SikaProof® Adhesive-02
SikaProof® Adhesive-02 is a 2-part, cement-modified adhesive. It is part of the SikaProof® A+ System and is used to post-apply the SikaProof® A+ membrane to the existing reinforced concrete structure.
- Good adhesion to concrete substrates
- Can be applied to damp concrete surfaces
- Easy to mix and apply
- Good resistance to lateral water migration
- Low VOC content
Usage
SikaProof® Adhesive-02 is used for:- Bonding the SikaProof® A+ 08 or SikaProof® A+ 12 waterproofing membrane to an exisiting reinforced concrete structure to form a fully-bonded membrane waterproofing system
- The Product may only be used by experienced professionals.
Advantages
- Good adhesion to concrete substrates
- Can be applied to damp concrete surfaces
- Easy to mix and apply
- Good resistance to lateral water migration
- Low VOC content
Packaging
Part A | 5.0 kg container |
Part B | 15.625 kg bag |
Part A and Part B | 20.625 kg pre-batched unit |
Refer to the current price list for available packaging variations.
Colour
Part A | white liquid |
Part B | white powder |
Product Details
ENVIRONMENTAL INFORMATION
Environmental Product Declaration (EPD) in accordance with EN 15804. EPD independently verified by Institut für Bauen und Umwelt e.V. (IBU)
APPROVALS / STANDARDS
CE marking and declaration of performance based on EN 1504-2:2004 Products and systems for the protection and repair of concrete structures — Surface protection systems for concrete — Coating
Chemical Base
Part A | Water based polymer dispersion |
Part B | Portland cement, selected aggregate and admixtures |
Shelf Life
12 months from date of production
Storage Conditions
The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.
Refer to the current Safety Data Sheet for information on safe handling and storage.
Density
1.9 g/cm3 (at +20 °C)
System Structure
The following products are part of the post-applied SikaProof® A+ system:
Function | Product |
Primer | SikaProof® Primer-02 |
Adhesive | SikaProof® Adhesive-02 |
Waterproofing membrane | SikaProof® A+ 08 SikaProof® A+ 12 |
Tape | SikaProof® ExTape-100 SikaProof® Sandwich Tape |
Tensile adhesion strength
2.1 N/mm2 | (EN 1542) |
Reaction to Fire
A2-s1,d0 | (EN 13501-1) |
Application
Mixing Ratio
A : B = 32 : 100 (parts by weight)
Product Temperature
Maximum | +30 °C |
Minimum | +5 °C |
Ambient Air Temperature
Maximum | +30 °C |
Minimum | +5 °C |
Substrate Temperature
Maximum | +30 °C |
Minimum | +5 °C |
Pot Life
at +20 °C | 40 minutes |
at +30 °C | 30 minutes |
Consumption
≥ 2.8 kg/m2
Note: Consumption data is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply the Product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.
SUBSTRATE PREPARATION
IMPORTANT
Strictly follow installation procedures
Strictly follow installation procedures as defined in Method Statements, application manuals and working instructions which must always be adjusted to the actual site conditions.
Prepare the substrate and prime it with SikaProof® Primer-02.
For more information, refer to the current Product Data Sheet of SikaProof® Primer-02 and Application Manual SikaProof® A+ Post-Applied.
MIXING
IMPORTANT
Mix only full units of part A and part B
- Shake part A (white liquid) until the liquid is homogenous.
- Pour part A into the mixing container.
- IMPORTANT Mix using an electric mixer (≥ 500 rpm) with helical paddle. While mixing add approximately 3/4 of part B (powder).
- Mix for 1 minute.
- Add the remainder of part B.
- Continue mixing for 3 minutes until a uniform and lump-free mix is achieved.
APPLICATION
IMPORTANT
Risk of improper bonding
Observe the pot life of the Product. The open time is reduced when applying the Product at high temperatures or in windy conditions.
- Apply the SikaProof® A+ 08 or SikaProof® A+ 12 membrane as soon as possible after applying the Product.
- Take precautionary measures when applying the Product in high temperatures or windy conditions.
For more application information, refer to the following resources:
Method Statement - SikaProof® A+
Application Manual SikaProof® A+ Post-Applied
CLEANING OF TOOLS
Clean all tools and application equipment with water immediately after use. Hardened material can only be removed mechanically.