Sikafloor®-330
Polyurethane elastic low VOC self-smoothing flooring resin
Sikafloor®-330 is a 2-part, polyurethane, elastic, low VOC self-smoothing flooring resin. It is part of the Sika Comfortfloor® decorative flooring range.
- Very low VOC emissions
- Soft underfoot
- Comfortable
- Reduces impact noise transmission and airborne noise
- Seamless
- Permanently elastic
- Good mechanical resistance
- Easy to apply
- Low maintenance finish
Usage
Decorative elastic smooth resin flooring wearing layer for:- Sika ComfortFloor® and Sika ComfortFloor® Pro Systems
- Hospitals
- Schools
- Retail areas
- Showrooms
- Entrance halls
- Lobbies
- Open-plan offices
- Museums
- Residential use
- Interior use only
Advantages
- Very low VOC emissions
- Soft underfoot
- Comfortable
- Reduces impact noise transmission and airborne noise
- Seamless
- Permanently elastic
- Good mechanical resistance
- Easy to apply
- Low maintenance finish
Packaging
| Part A | 15.8 kg container |
| Part B | 4.2 kg container |
| Part A+B | 20 kg ready to mix unit |
Refer to current price list for packaging variations
Colour
Final floor appearance: Smooth matt finish
| Part A - resin | liquid / coloured |
| Part B - hardener | liquid / light brown, transparent |
Available in RAL 1014, RAL 2000, RAL 3009, RAL 5015, RAL 6010, RAL 7042, RAL 8002, RAL 9001, RAL 9005
The colour of the Sikafloor®-330 has to be approximately adjusted to the colour of the Sikafloor®-305 W seal / top coat.
Applied colours selected from colour charts will be approximate.
For colour matching: Apply colour sample and confirm selected colour under real lighting conditions.
When product is exposed to direct sunlight, there may be some discolouration and colour variation, this has no influence on the function and performance of the floor finish.
Product Details
ENVIRONMENTAL INFORMATION
- Conformity with LEED v4 MRc 2 (Option 1): Building Product Disclosure and Optimization – Environmental Product Declarations - Sikafloor®-330.
- Conformity with LEED v4 MRc 4 (Option 2): Building Product Disclosure and Optimization - Material Ingredients - Sikafloor®-330.
- Conformity with LEED v2009 IEQc 4.2: Low-Emitting Materials - Paints and Coatings - Sikafloor®-330.
- IBU Environmental Product Declaration (EPD).
APPROVALS / STANDARDS
- CE Marking and Declaration of Performance to EN 13813 - Resin screed material for internal use in buildings.
- CE Marking and Declaration of Performance to EN 1504-2 - Surface protection product for concrete - Coating.
- Determination of Fire Behaviour EN ISO 9239-1, Sikafloor®-305 W/-330/-Comfort Porefiller/-Comfort Regupol 6015H/-Comfort Adhesive, Universiteit Gent Netherlands, Test report No. 08-198.
- Cleanroom Suitability Sikafloor®, Fraunhofer IPA, Report No. SI 1008-533.
- VOC Emissions AgBB, Sikafloor®-330, eurofins, Certificate No. 765863F, 770029B, 7712844A.
- Impact Sound Reduction EN 140-8, Sika Comfortfloor® / Comfortfloor® Pro / Comfortfloor® Decorative / Comfortfloor® Decorative Pro, Gottfried & Rolof Institut Germany, Test report No. 102-B-08.
- Determination of Wear Resistance EN 651, EN 424, EN 425, Sikafloor®-156/305 W/-330/-Comfort Porefiller/-Comfort Regupol 6015H/-Comfort Adhesive, TFI, Test report No. 391580-02.
Chemical Base
Polyurethane
Shelf Life
6 months from date of production
Storage Conditions
The product must be stored in original, unopened and undamaged packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.
Density
| Resin mixed | ~1.40 kg/l |
Values at +23 °C
Solid content by mass
~100 %
Solid content by volume
~100 %
Shore A Hardness
| ~80 (14 days / +23 °C) | (DIN 53505) |
Tensile Strength
| > 8.0 N/mm² (14 days / +23 °C) | (DIN 53504) |
Tensile adhesion strength
| > 1.5 N/mm2 (failure in concrete) | (EN 13892-8) |
Tear Strength
| ~25 N/mm (14 days / +23 °C) | (ISO 34-1) |
Chemical Resistance
Sikafloor®-330 must always be sealed with Sikafloor®-305 W and provides the chemical resistance. Refer to Product Data Sheet.
Application
Mixing Ratio
Part A : Part B = 79 : 21 (by weight)
Layer Thickness
~2.0 mm at 2.8 kg/m²
Refer to the System Data Sheets: Sika Comfortfloor® PS-23, Sika Comfortfloor® PS-63, Sika Comfortfloor® PS-65
Product Temperature
+15 °C min. / +30 °C max.
Ambient Air Temperature
+15 °C min. / +30 °C max.
Relative Air Humidity
80 % max.
Dew Point
Beware of condensation.
The substrate and uncured applied floor material must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+15 °C min. / +30 °C max.
Substrate Moisture Content
≤4 % parts by weight
The following test methods can be used: Sika®-Tramex meter, CM-measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
| Temperature | Time |
| +10 °C | ~21 minutes |
| +20 °C | ~15 minutes |
| +30 °C | ~12 minutes |
Curing Time
Before overcoating Sikafloor®-330 allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 24 hours | 72 hours |
| +20 °C | 16 hours | 48 hours |
| +30 °C | 16 hours | 36 hours |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
| Temperature | Foot traffic | Full cure |
| +10 °C | ~24 hours | ~9 days |
| +20 °C | ~18 hours | ~7 days |
| +30 °C | ~16 hours | ~5 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Consumption
~1.4 kg/m2/mm
MIXING
Prior to mixing all parts, mix separately Part A (resin) using the electric mixing equipment. Mix liquid and all the coloured pigment until a uniform colour / mix has been achieved. Add Part B (hardener) to Part A and mix Part A + B continuously for 2 minutes until a uniformly coloured mix has been achieved. To ensure thorough mixing pour materials into a clean container and mix again for at least 1 minute to achieve a smooth consistent mix. Excessive mixing must be avoided to minimise air entrainment. During the final mixing stage, scrape down the sides and bottom of the mixing container with a straight edge trowel or spatula at least once to ensure complete mixing. Mix full units only. Mixing time for A+B = ~3 minutes.
APPLICATION
Strictly follow installation procedures as defined in method statements, application manuals and working instructions which must always be adjusted to the actual site conditions.
Prior to application, confirm substrate moisture content, relative air humidity, dew point, substrate, air and product temperatures. If moisture content > 4% parts by weight, Sikafloor® EpoCem® may be applied as a Temporary Moisture Barrier (T.M.B.) system.
Pour mixed Sikafloor®-330 onto the prepared substrate and spread evenly using a suitable trowel or pin leveller to the required thickness.
Spike roller immediately in two directions at right angles to each other to remove trowel marks, aid air release, ensure an even thickness and obtain the required surface finish. A seamless finish can be achieved if a ‘wet’ edge is maintained during application. When Sikafloor®-330 is “tack-free”, apply the Sikafloor®-305 W seal coat.
CLEANING OF TOOLS
Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened material can only be removed mechanically.
CLEANING
Refer to Sika Information Manual: Sikafloor®-Cleaning Regime