Sikafloor®-378
Epoxy based tough-flexible coloured flooring seal coat
Sikafloor®-378 is a 2-part, epoxy based, coloured, flooring seal coat with improved resistance against amine blushing under critical weather conditions. It provides a hard wearing, abrasion and chemical resistant gloss finish over aggregate broadcast Sikafloor® epoxy or polyurethane resin floors. Internal use.
- Improved resistance against amine blushing.
- Good abrasion resistance.
- Good mechanical and chemical resistance.
- Good opacity.
- Gloss finish.
- Slip resistant surface to suit clients requirements.
Usage
- Seal coat for Sikafloor® industrial flooring broadcast systems.
- Top coat on Sikafloor® flooring systems.
- Suitable for slip resistant broadcast systems on car park decks, ramps and warehouse floors.
Advantages
- Improved resistance against amine blushing.
- Good abrasion resistance.
- Good mechanical and chemical resistance.
- Good opacity.
- Gloss finish.
- Slip resistant surface to suit clients requirements.
Packaging
Part A | 24,6 kg container |
Part B | 5,4 kg container |
Part A+B | 30 kg ready to mix unit |
Colour
Final floor appearance: Gloss finish
Resin - Part A | coloured, liquid |
Hardener - Part B | transparent, liquid |
Standard colours: ~RAL 3003, RAL 5010, RAL 6010, RAL 7016, RAL 7031
Applied colours selected from colour charts will be approximate.
For colour matching: Apply colour sample and confirm selected colour under real lighting conditions.
When product is exposed to direct sunlight, there may be some discolouration and colour variation, this has no influence on the function and performance of the coating.
Product Details
ENVIRONMENTAL INFORMATION
- Conformity with LEED v4 MRc 2 (Option 1): Building Product Disclosure and Optimization – Environmental Product Declarations.
- Conformity with LEED v4 MRc 4 (Option 2): Building Product Disclosure and Optimization - Material Ingredients.
- Conformity with LEED v2009 IEQc 4.2: Low-Emitting Materials - Paints and Coatings.
- IBU Environmental Product Declaration (EPD).
APPROVALS / STANDARDS
- CE Marking and Declaration of Performance to EN 1504-2 - Surface protection product for concrete - Coating.
- CE Marking and Declaration of Performance to EN 13813 - Resin screed material for internal use in buildings.
- Grip test, Sikafloor®-161 / -350 N / -378, kiwa, Report No. P 9477-2.
- Coating system DAfStb Test Class OS 11, Sikaflooor® MultiFlex PB-55, kiwa, Test report No. P 10777-1.
- Coating system DAfStb Test Class OS 11, Sikaflooor® MultiFlex PB-56, kiwa, Test report No. P 10777-2.
- Sliding test DIN 51131, Sikafloor®-378 / -81 EpoCem, Roxeler, Certificate No. 020044-17-8a.
Product Declaration
EN 1504-2: Surface protection product for concrete - Coating.
EN 13813: Resin screed material for internal use in buildings
Chemical Base
Epoxy
Shelf Life
24 months from date of production
Storage Conditions
The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.
Density
Part A | ~1.64 kg/l |
Part B | ~1.00 kg/l |
Resin mixed | ~1.40 kg/l |
All Density values at +23 °C.
Solid content by mass
~99 %
Solid content by volume
~99 %
Shore D Hardness
~75 (7 days / +23 °C) | (DIN 53 505) |
Abrasion Resistance
24 mg (CS 10/1000/1000) (8 days / +23 °C) | (DIN 53 109) |
Compressive Strength
~65 N/mm2 (28 days / +23 °C) | (EN 196-1) |
Tensile adhesion strength
> 1.5 N/mm² (failure in concrete) | (ISO 4624) |
Thermal Resistance
Exposure* | Dry heat |
Permanent | +50 °C |
Short-term max. 7 days | +80 °C |
Short-term max. 12 hours | +100 °C |
Short-term moist/wet heat* up to +60 °C where exposure is only occasional (steam cleaning etc.).
*No simultaneous chemical and mechanical exposure and only in combination with Sikafloor® systems as a broadcast system with approx. 3 - 4 mm thickness.
Chemical Resistance
Resistant to many chemicals. Contact Sika Technical Services for additional information
Application
Mixing Ratio
Part A : Part B = 82 : 18 (by weight)
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
80 % max.
Dew Point
Beware of condensation.
The substrate and uncured applied floor material must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Low temperatures and high humidity conditions increase the probability of blooming.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
≤ 4 % parts by weight
Test method: Sika®-Tramex meter, CM-measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperature | Time |
+10 °C | ~50 minutes |
+20 °C | ~25 minutes |
+30 °C | ~15 minutes |
Curing Time
Before applying Sikafloor®-378 on Sikafloor®-378 allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 30 hours | 3 days |
+20 °C | 24 hours | 2 days |
+30 °C | 16 hours | 1 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | ~72 hours | ~6 days | ~10 days |
+20 °C | ~24 hours | ~4 days | ~7 days |
+30 °C | ~18 hours | ~2 days | ~5 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Consumption
~0.7–0.9 kg/m² applied as a roller coating
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc. For detailed information, refer to the System Data Sheets: Sikafloor® Multiflex PB-21, Sikafloor® Multiflex PB-52.
MIXING
Prior to mixing all parts, mix separately Part A (resin) using a low speed single paddle electric stirrer (300–400 rpm) other suitable equipment. Mix liquid and all the coloured pigment until a uniform colour has been achieved. Add Part B (hardener) to Part A and mix Part A + B continuously for 3 minutes until a uniformly coloured mix has been achieved then, if required, gradually add the appropriate amount of Sika® Extender T. Mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing, pour materials into another container and mix again to achieve a smooth consistent mix. Excessive mixing must be avoided to minimise air entrainment. During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing. Mix full units only. Mixing time for A + B + Sika® Extender T (if required) = 5 minutes.
APPLICATION
Strictly follow installation procedures as defined in method statements, application manuals and working instructions which must always be adjusted to the actual site conditions.
Prior to application, confirm substrate moisture content, relative air humidity, dew point, substrate, air and product temperatures.
Seal coat
After waiting the appropriate overcoating time / curing, pour the mixed material onto the slip resistant broadcast layer and spread evenly using a squeegee at the required consumption rate to completely encapsulate the sand. Then using a short-piled roller, back roller in two directions at right angles to each other. A seamless finish can be achieved if a ‘wet’ edge is maintained during application.
CLEANING OF TOOLS
Clean all tools and application equipment with Thinner C immediately after use. Hardened material can only be removed mechanically.
CLEANING
To maintain the appearance of the floor after application, Sikafloor®-378 must have all spillages removed immediately and must be regularly cleaned using rotary brush, mechanical scrubbers, scrubber dryer, high pressure washer, wash and vacuum techniques etc. using suitable detergents and waxes. Refer to Sika Method Statement: Sikafloor®-Cleaning Regime.