Sika® Ucrete® FL

• Halal Certification Europe (HCE), Sika® Ucrete®, WHFC, Certificate No. 21453-2/1/1/Y1

• Food and Beverage Facilities Suitability, Sika® Ucrete®, HACCP, Test Report No. I-PE-769-SA-2-RG-06b

• Indoor Air Comfort Gold EN 16516, Sika® Ucrete®, eurofins, Certificate No. IACG-321-01-01-2023

Water-based polyurethane cement hybrid

Always refer to the best-before date of the individual packaging.

The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to the packaging.

Refer to the current Safety Data Sheet for information on safe handling and storage.

Laboratory-defined resistance to many individual chemicals. Before proceeding, contact Sika Technical Service for specific information.

~12–100 mm

Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.

2.3 kg/m² per mm of thickness

Note: Consumption data is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply the Product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.

IMPORTANT

Reduced service life due to incorrect treatment of cracks

The incorrect assessment and treatment of cracks may lead to a reduced service life and reflective cracking.

1. For static cracks, ensure the width is suitable for overcoating with Sika® Ucrete® FL.
2. For dynamic cracks, ensure the movement is within the movement capacity of Sika® Ucrete® FL.

TREATMENT OF JOINTS AND CRACKS

Construction joints and existing static surface cracks in substrate require pre-treating before full layer application. Use Sikadur® or Sikafloor® resins.

The Product can be applied on green or damp concrete with no standing water. Allow for at least 3 days for early concrete shrinkage to occur to prevent shrinkage cracks from appearing on the wearing surface.

Cementitious substrates must be structurally sound and of sufficient compressive strength (minimum 30 N/mm²) with a minimum tensile strength of 1.5 N/mm².

Substrates must be clean, dry and free of contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.

MECHANICAL SUBSTRATE PREPARATION

IMPORTANT

Surface defects due to voids in the substrate

Voids and blow holes in the substrate will weaken the surface and damage the covering Product if not repaired during the preparation process.

1. Fully expose blow holes and voids during surface preparation to identify the required repairs.

1. Remove weak cementitious substrates.
2. Prepare cementitious substrates mechanically using abrasive blast cleaning, abrasive planing or scarifying equipment to remove cement laitance.
3. Cut retaining grooves in the substrate along all exposed edges (perimeter, joints, connections, plinths, columns, covings and drains or gullies).
4. Before applying the Product, remove all dust, loose and friable material from the application surface with an industrial vacuuming equipment.

For additional information on products for leveling and repairing defects, contact Sika® Technical Services.

SUBSTRATE PREPARATION OF NON-CEMENTITIOUS SUBSTRATES

For information on substrate preparation of non-cementitious substrates, contact Sika® Technical Services.

IMPORTANT

Protecting the material after application

After application, protect the System from damp, condensation and direct water contact for at least 24 hours.

IMPORTANT

Protect from overhead leaks and condensation

Protect the Product during application from pipe condensation or any overhead leaks.

IMPORTANT

Ventilation in confined spaces

Always ensure good ventilation when applying the Product in a confined space.

IMPORTANT

Application on polymer modified cement mortars

Do not apply the product on polymer modified cement mortars if the mortar expands when sealed with an impervious resin.

IMPORTANT

Waiting time for foodstuff

Allow a minimum of 48 hours after application before placing foodstuff in the same area.

Excessive waiting period or early exposure to moisture causing reduced adhesion between coats

Note: If the time between coats exceeds 48 hours, or if condensation or water impacts the surface during this time the adhesion of the subsequent layer may be reduced.

1. Fully abrade the surface prior to the application of the subsequent overlay.

RESIN SCREED

1. Pour the mixed Product onto the prepared substrate.
2. Spread and compact the Product with a trowel to the required thickness between screed rails or battens, if installed.
3. Level the screed surface with a levelling beam spanning onto the screed rails or battens.
4. Finish the surface to the required surface texture with trowels or walk-behind power float.

Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened material can only be removed mechanically.